View AM29LV128M_197237.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ADVANCE INFORMATION
AM29LV128M
128 Megabit (8 M x 16-Bit/16 M x 8-Bit) MirrorBit 3.0 Volt-only Uniform Sector Flash Memory with Enhanced VersatileI/O Control
DISTINCTIVE CHARACTERISTICS
ARCHITECTURAL ADVANTAGES s Single power supply operation -- 3 volt read, erase, and program operations s Enhanced VersatileI/O control -- Device generates and tolerates voltages on all I/Os and control inputs as determined by the voltage on the VIO pin; operates from 1.65 to 3.6 V (see page 8) s Manufactured on 0.23 m MirrorBit process technology s SecSi (Secured Silicon) Sector region -- 128-word/256-byte sector for permanent, secure identification through an 8-word/16-byte random Electronic Serial Number, accessible through a command sequence -- May be programmed and locked at the factory or by the customer s Flexible sector architecture -- Two hundred fifty-six 32 Kword (64 Kbyte) sectors s Compatibility with JEDEC standards -- Provides pinout and software compatibility for single-power supply flash, and superior inadvertent write protection s Minimum 100,000 erase cycle guarantee per sector s 20-year data retention at 125C PERFORMANCE CHARACTERISTICS s High performance -- 90 ns access time -- 25 ns page read times -- 0.4 s typical sector erase time -- 5.9 s typical write buffer word programming time: 16-word/32-byte write buffer reduces overall programming time for multiple-word updates -- 4-word/8-byte page read buffer -- 16-word/32-byte write buffer s Low power consumption (typical values at 3.0 V, 5 MHz) -- 30 mA typical active read current -- 50 mA typical erase/program current -- 1 A typical standby mode current s Package options -- 56-pin TSOP -- 64-ball Fortified BGA SOFTWARE & HARDWARE FEATURES s Software features -- Program Suspend & Resume: read other sectors before programming operation is completed -- Erase Suspend & Resume: read/program other sectors before an erase operation is completed -- Data# polling & toggle bits provide status -- Unlock Bypass Program command reduces overall multiple-word or byte programming time -- CFI (Common Flash Interface) compliant: allows host system to identify and accommodate multiple flash devices s Hardware features -- Sector Protection: hardware-level method of preventing write operations within a sector -- Temporary Sector Unprotect: VID-level method of changing code in locked sectors -- WP#/ACC input accelerates programming time (when high voltage is applied) for greater throughput during system production. Protects first or last sector regardless of sector protection settings -- Hardware reset input (RESET#) resets device -- Ready/Busy# output (RY/BY#) detects program or erase cycle completion
This Data Sheet states AMD's current technical specifications regarding the Products described herein. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications.
Publication# 25270 Rev: B Amendment/+1 Issue Date: September 17, 2002
Refer to AMD's Website (www.amd.com) for the latest information.
ADVANCE
INFORMATION
GENERAL DESCRIPTION
The AM29LV128M is a 128 Mbit, 3.0 volt single power supply flash memory devices organized as 8,388,608 words or 16,777,216 bytes. The device has a 16-bit wide data bus that can also function as an 8-bit wide data bus by using the BYTE# input. The device can be programmed either in the host system or in standard EPROM programmers. An access time of 90, 100, 110, or 120 ns is available. Note that each access time has a specific operating voltage range (VCC) and an I/O voltage range (VIO), as specified in the Product Selector Guide and the Ordering Information sections. The device is offered in a 56-pin TSOP, 64-ball Fortified BGA, or 63-ball Fine-Pitch BGA package. Each device has separate chip enable (CE#), write enable (WE#) and output enable (OE#) controls. Each device requires only a single 3.0 volt power supply for both read and write functions. In addition to a V CC input, a high-voltage accelerated program (WP#/ACC) input provides shorter programming times through increased current. This feature is intended to facilitate factory throughput during system production, but may also be used in the field if desired. The device is entirely command set compatible with the JEDEC single-power-supply Flash standard. Commands are written to the device using standard microprocessor write timing. Write cycles also internally latch addresses and data needed for the programming and erase operations. The sector erase architecture allows memory sectors to be erased and reprogrammed without affecting the data contents of other sectors. The device is fully erased when shipped from the factory. Device programming and erasure are initiated through command sequences. Once a program or erase operation has begun, the host system need only poll the DQ7 (Data# Polling) or DQ6 (toggle) status bits or monitor the Ready/Busy# (RY/BY#) output to determine whether the operation is complete. To facilitate programming, an Unlock Bypass mode reduces command sequence overhead by requiring only two write cycles to program data instead of four. The Enhanced VersatileI/OTM (VIO) control allows the host system to set the voltage levels that the device generates and tolerates on all I/Os and control inputs to the same voltage level that is asserted on the V IO pin. This allows the device to operate in a 1.8 V or 3 V system environment as required. Hardware data protection measures include a low V CC detector that automatically inhibits write operations during power transitions. The hardware sector protection feature disables both program and erase operations in any combination of sectors of memory. This can be achieved in-system or via programming equipment. The Erase Suspend/Erase Resume feature allows the host system to pause an erase operation in a given sector to read or program any other sector and then complete the erase operation. The Program Suspend/Program Resume feature enables the host system to pause a program operation in a given sector to read any other sector and then complete the program operation. The hardware RESET# pin terminates any operation in progress and resets the device, after which it is then ready for a new operation. The RESET# pin may be tied to the system reset circuitry. A system reset would thus also reset the device, enabling the host system to read boot-up firmware from the Flash memory device. The device reduces power consumption in the standby mode when it detects specific voltage levels on CE# and RESET#, or when addresses have been stable for a specified period of time. The SecSi (Secured Silicon) Sector provides a 128-word/256-byte area for code or data that can be permanently protected. Once this sector is protected, no further changes within the sector can occur. The Write Protect (WP#/ACC) feature protects the first or last sector by asserting a logic low on the WP# pin. AMD MirrorBit flash technology combines years of Flash memory manufacturing experience to produce the highest levels of quality, reliability and cost effectiveness. The device electrically erases all bits within a sector simultaneously via hot-hole assisted erase. The data is programmed using hot electron injection.
RELATED DOCUMENTS
For a comprehensive information on MirrorBit products, including migration information, data sheets, application notes, and software drivers, please see www.amd.comFlash MemoryProduct InformationMirrorBitFlash InformationTechnical Documentation. The following is a partial list of documents closely related to this product: MirrorBitTM Flash Memory Write Buffer Programming and Page Buffer Read Implementing a Common Layout for AMD MirrorBit and Intel StrataFlash Memory Devices Migrating from Single-byte to Three-byte Device IDs Am29LV256M, 256 Mbit MirrorBit Flash device (in 64-ball, 18 x 12 mm Fortified BGA package) September 17, 2002
2
AM29LV128M
ADVANCE
INFORMATION
TABLE OF CONTENTS
Product Selector Guide . . . . . . . . . . . . . . . . . . . . . 4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Connection Diagrams . . . . . . . . . . . . . . . . . . . . . . 5 Special Package Handling Instructions .................................... 6 Pin Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Logic Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . 8 Device Bus Operations . . . . . . . . . . . . . . . . . . . . 10
Table 1. Device Bus Operations ..................................................... 10 Figure 6. Erase Operation .............................................................. 33
Command Definitions ............................................................. 34
Table 9. Command Definitions (x16 Mode, BYTE# = VIH) ............. 34 Table 10. Command Definitions (x8 Mode, BYTE# = VIL).............. 35
Write Operation Status . . . . . . . . . . . . . . . . . . . . . 36 DQ7: Data# Polling ................................................................. 36
Figure 7. Data# Polling Algorithm .................................................. 36
RY/BY#: Ready/Busy# ............................................................ 37 DQ6: Toggle Bit I .................................................................... 37
Figure 8. Toggle Bit Algorithm ........................................................ 38
Word/Byte Configuration ........................................................ 10 Enhanced VersatileIO (VIO) Control .................................... 10 Requirements for Reading Array Data ................................... 11
Page Mode Read ............................................................................11
Writing Commands/Command Sequences ............................ 11
Write Buffer .....................................................................................11 Accelerated Program Operation ......................................................11 Autoselect Functions .......................................................................11
DQ2: Toggle Bit II ................................................................... 38 Reading Toggle Bits DQ6/DQ2 ............................................... 38 DQ5: Exceeded Timing Limits ................................................ 39 DQ3: Sector Erase Timer ....................................................... 39 DQ1: Write-to-Buffer Abort ..................................................... 39
Table 11. Write Operation Status................................................... 39
Absolute Maximum Ratings. . . . . . . . . . . . . . . . . 40
Figure 9. Maximum Negative Overshoot Waveform ..................... 40 Figure 10. Maximum Positive Overshoot Waveform ..................... 40
Standby Mode ........................................................................ 11 Automatic Sleep Mode ........................................................... 12 RESET#: Hardware Reset Pin ............................................... 12 Output Disable Mode .............................................................. 12
Table 2. Sector Address Table........................................................ 13
Operating Ranges . . . . . . . . . . . . . . . . . . . . . . . . . 40 DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 41 Test Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Figure 11. Test Setup .................................................................... 42 Table 12. Test Specifications ......................................................... 42
Autoselect Mode ..................................................................... 19
Table 3. Autoselect Codes, (High Voltage Method) ....................... 19
Sector Protection and Unprotection ........................................ 19 Write Protect (WP#) ................................................................ 20 Temporary Sector Unprotect .................................................. 20
Figure 1. Temporary Sector Unprotect Operation ...........................20 Figure 2. In-System Sector Group Protect/Unprotect Algorithms ...21
Key to Switching Waveforms. . . . . . . . . . . . . . . . 42
Figure 12. Input Waveforms and Measurement Levels ...................................................................... 42
AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 43 Read-Only Operations ........................................................... 43
Figure 13. Read Operation Timings ............................................... 43 Figure 14. Page Read Timings ...................................................... 44
SecSi (Secured Silicon) Sector Flash Memory Region .......... 22
Table 4. SecSi Sector Contents ...................................................... 22
Hardware Data Protection ...................................................... 22
Low VCC Write Inhibit .....................................................................22 Write Pulse "Glitch" Protection ........................................................23 Logical Inhibit ..................................................................................23 Power-Up Write Inhibit ....................................................................23
Hardware Reset (RESET#) .................................................... 45
Figure 15. Reset Timings ............................................................... 45
Erase and Program Operations .............................................. 46
Figure 16. Program Operation Timings .......................................... 47 Figure 17. Accelerated Program Timing Diagram .......................... 47 Figure 18. Chip/Sector Erase Operation Timings .......................... 48 Figure 19. Data# Polling Timings (During Embedded Algorithms) . 49 Figure 20. Toggle Bit Timings (During Embedded Algorithms) ...... 50 Figure 21. DQ2 vs. DQ6 ................................................................. 50
Common Flash Memory Interface (CFI) . . . . . . . 23
Table 5. CFI Query Identification String ..........................................23 Table 6. System Interface String..................................................... 24 Table 7. Device Geometry Definition ..............................................24 Table 8. Primary Vendor-Specific Extended Query ........................25
Temporary Sector Unprotect .................................................. 51
Figure 22. Temporary Sector Group Unprotect Timing Diagram ... 51 Figure 23. Sector Group Protect and Unprotect Timing Diagram .. 52
Command Definitions . . . . . . . . . . . . . . . . . . . . . 25 Reading Array Data ................................................................ 25 Reset Command ..................................................................... 26 Autoselect Command Sequence ............................................ 26 Enter SecSi Sector/Exit SecSi Sector Command Sequence .. 26 Word/Byte Program Command Sequence ............................. 26
Unlock Bypass Command Sequence ..............................................27 Write Buffer Programming ...............................................................27 Accelerated Program ......................................................................28 Figure 3. Write Buffer Programming Operation ...............................29 Figure 4. Program Operation ..........................................................30
Alternate CE# Controlled Erase and Program Operations ..... 53
Figure 24. Alternate CE# Controlled Write (Erase/Program) Operation Timings .......................................................................... 54
Program Suspend/Program Resume Command Sequence ... 30
Figure 5. Program Suspend/Program Resume ...............................31
Chip Erase Command Sequence ........................................... 31 Sector Erase Command Sequence ........................................ 31 Erase Suspend/Erase Resume Commands ........................... 32
Latchup Characteristics . . . . . . . . . . . . . . . . . . . . 54 Erase And Programming Performance. . . . . . . . 55 TSOP Pin and BGA Package Capacitance . . . . . 55 Data Retention. . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . 56 TS056/TSR056--56-Pin Standard/Reverse Thin Small Outline Package (TSOP) ..................................................................... 56 LAA064--64-Ball Fortified Ball Grid Array 13 x 11 mm Package .............................................................. 57 Revision Summary . . . . . . . . . . . . . . . . . . . . . . . . 58
September 17, 2002
AM29LV128M
3
ADVANCE
INFORMATION
PRODUCT SELECTOR GUIDE
Part Number Regulated Voltage Range VCC = 3.0-3.6 V Full Voltage Range VCC = 2.7-3.6 V VIO = 3.0-3.6 V VIO = 1.65-1.95 V VIO = 2.7-3.6 V VIO = 1.65-1.95 V 90 90 25 25 93R 98R 103R 108R 103 108 100 100 30 30 AM29LV128M 113R 118R 113 118 110 110 40 40 123R 128R 123 128 120 120 40 40
Speed/ Voltage Option
Max. Access Time (ns) Max. CE# Access Time (ns) Max. Page access time (tPACC) Max. OE# Access Time (ns)
Note: 1. See "AC Characteristics" for full specifications. 2. For the AM29LV128M Enhanced-VIO device, the last digit of the speed indicator specifies VIO range. Speed grades ending in 3 (such as 93, 103, etc.) indicate a 3 Volt VIO range; speed grades ending in 8 (such as 98, 108, etc.) indicate a 1.8V VIO range.
BLOCK DIAGRAM
RY/BY# VCC VSS VIO RESET# WE# WP#/ACC BYTE# Erase Voltage Generator Input/Output Buffers Sector Switches DQ0-DQ15 (A-1)
State Control Command Register
PGM Voltage Generator Chip Enable Output Enable Logic STB Data Latch
CE# OE#
STB VCC Detector Timer Address Latch
Y-Decoder
Y-Gating
X-Decoder
Cell Matrix
A22-A0
4
AM29LV128M
September 17, 2002
ADVANCE
INFORMATION
CONNECTION DIAGRAMS
NC A22 A15 A14 A13 A12 A11 A10 A9 A8 A19 A20 WE# RESET# A21 WP#/ACC RY/BY# A18 A17 A7 A6 A5 A4 A3 A2 A1 NC NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 NC NC A16 BYTE# VSS DQ15/A-1 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VCC DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE# VSS CE# A0 NC VIO
56-Pin Standard TSOP
NC NC A16 BYTE# VSS DQ15/A-1 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VCC DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE# VSS CE# A0 NC VIO
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
56-Pin Reverse TSOP
56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29
NC A22 A15 A14 A13 A12 A11 A10 A9 A8 A19 A20 WE# RESET# A21 WP#/ACC RY/BY# A18 A17 A7 A6 A5 A4 A3 A2 A1 NC NC
September 17, 2002
AM29LV128M
5
ADVANCE
INFORMATION
CONNECTION DIAGRAMS
Fortified BGA Top View, Balls Facing Down
A8 NC A7 A13 A6 A9 A5 WE# A4
B8 A22 B7 A12 B6 A8 B5 RESET# B4
C8 NC C7 A14 C6 A10 C5 A21 C4 A18 C3 A6 C2 A2 C1 NC
D8 VIO D7 A15 D6 A11 D5 A19 D4 A20 D3 A5 D2 A1 D1 NC
E8 VSS E7 A16 E6 DQ7 E5 DQ5 E4 DQ2 E3 DQ0 E2 A0 E1 NC
F8 NC F7
G8 NC G7
H8 NC H7 VSS H6 DQ6 H5 DQ4 H4 DQ3 H3 DQ1 H2 VSS H1 NC
BYTE# DQ15/A-1 F6 DQ14 F5 DQ12 F4 DQ10 F3 DQ8 F2 CE# F1 VIO G6 DQ13 G5 VCC G4 DQ11 G3 DQ9 G2 OE# G1 NC
RY/BY# WP#/ACC A3 A7 A2 A3 A1 NC B3 A17 B2 A4 B1 NC
Note: The FBGA package pinout configuration shown is preliminary. The ball count and package physical dimensions have not yet been determined. Contact AMD for further information.
Special Package Handling Instructions
Special handling is required for Flash Memory products in molded packages (TSOP, BGA, SSOP, PLCC, PDIP). The package and/or data integrity may be
compromised if the package body is exposed to temperatures above 150C for prolonged periods of time.
6
AM29LV128M
September 17, 2002
ADVANCE
INFORMATION
PIN DESCRIPTION
A22-A0 = 23 Address inputs DQ14-DQ0 = 15 Data inputs/outputs DQ15/A-1 CE# OE# WE# WP#/ACC RESET# BYTE# RY/BY# VCC = DQ15 (Data input/output, word mode), A-1 (LSB Address input, byte mode) = Chip Enable input = Output Enable input = Write Enable input = Hardware Write Protect input; Acceleration input = Hardware Reset Pin input = Selects 8-bit or 16-bit mode = Ready/Busy output = 3.0 volt-only single power supply (see Product Selector Guide for speed options and voltage supply tolerances) = Output Buffer power = Device Ground = Pin Not Connected Internally
LOGIC SYMBOL
23 A22-A0 CE# OE# WE# WP#/ACC RESET# VIO BYTE# RY/BY# DQ15-DQ0 (A-1) 16 or 8
VIO VSS NC
September 17, 2002
AM29LV128M
7
ADVANCE
INFORMATION
ORDERING INFORMATION Standard Products
AMD standard products are available in several packages and operating ranges. The order number (Valid Combination) is formed by a combination of the following: AM29LV128M H 93R PC I
TEMPERATURE RANGE I = Industrial (-40C to +85C) PACKAGE TYPE E = 56-Pin Thin Small Outline Package (TSOP) Standard Pinout (TS 056) F = 56-Pin Thin Small Outline Package (TSOP) Reverse Pinout (TSR056) PC = 64-Ball Fortified Ball Grid Array (FBGA), 1.0 mm pitch, 13 x 11 mm package (LAA064) SPEED OPTION See Product Selector Guide and Valid Combinations SECTOR ARCHITECTURE AND SECTOR WRITE PROTECTION (WP# = VIL) H = Uniform sector device, highest address sector protected L = Uniform sector device, lowest address sector protected DEVICE NUMBER/DESCRIPTION AM29LV128MH/L 128 Megabit (8 M x 16-Bit/16 M x 8-Bit) MirrorBit Uniform Sector Flash Memory with Enhanced VersatileIO Control, 3.0 Volt-only Read, Program, and Erase
Valid Combinations for TSOP Package AM29LV128MH93R AM29LV128ML93R AM29LV128MH98R AM29LV128ML98R AM29LV128MH103 AM29LV128ML103 AM29LV128MH108 AM29LV128ML108 AM29LV128MH113 AM29LV128ML113 AM29LV128MH118 AM29LV128ML118 AM29LV128MH123 AM29LV128ML123 AM29LV128MH128 AM29LV128ML128 AM29LV128MH103R AM29LV128ML103R AM29LV128MH108R AM29LV128ML108R AM29LV128MH113R AM29LV128ML113R AM29LV128MH118R AM29LV128ML118R AM29LV128MH123R AM29LV128ML123R AM29LV128MH128R AM29LV128ML128R EI, FI
Speed (ns)
VIO Range 3.0-3.6 V
VCC Range
90 1.65-1.95 V 2.7-3.6 V 100 1.65-1.95 V 2.7-3.6 V 110 1.65-1.95 V 2.7-3.6 V 120 1.65-1.95 V 3.0-3.6 V 100 1.65-1.95 V 3.0-3.6 V 110 1.65-1.95 V 3.0-3.6 V 120 1.65-1.95 V
3.0-3.6 V
2.7-3.6 V
3.0-3.6 V
8
AM29LV128M
September 17, 2002
ADVANCE
Valid Combinations for Fortified BGA Package Order Number AM29LV128MH93R AM29LV128ML93R AM29LV128MH98R AM29LV128ML98R AM29LV128MH103 AM29LV128ML103 AM29LV128MH108 AM29LV128ML108 AM29LV128MH113 AM29LV128ML113 AM29LV128MH118 AM29LV128ML118 AM29LV128MH123 AM29LV128ML123 AM29LV128MH128 AM29LV128ML128 AM29LV128MH103R AM29LV128ML103R AM29LV128MH108R AM29LV128ML108R AM29LV128MH113R AM29LV128ML113R AM29LV128MH118R AM29LV128ML118R AM29LV128MH123R AM29LV128ML123R AM29LV128MH128R AM29LV128ML128R Package Marking L128MH93N L128ML93N L128MH98N L128ML98N L128MH103P L128ML103P L128MH108P L128ML108P L128MH113P L128ML113P L128MH118P L128ML118P L128MH123P L128ML123P L128MH128P L128ML128P L128MH103N L128ML103N L128MH108N L128ML108N L128MH113N L128ML113N L128MH118N L128ML118N L128MH123N L128ML123N L128MH128N L128ML128N
INFORMATION
VCC Speed VIO Range Range (ns)
90
3.0- 3.6 V 2.7- 3.6 V 1.65- 1.95 V 2.7- 3.6 V 1.65- 1.95 V 2.7- 3.6 V 1.65- 1.95 V 3.0- 3.6 V 1.65- 1.95 V 3.0- 3.6 V 1.65- 1.95 V 3.0- 3.6 V 1.65- 1.95 V
3.0- 3.6 V
100
110
2.7- 3.6 V
PCI
I
120
100
110
3.0- 3.6 V
120
Valid Combinations Valid Combinations list configurations planned to be supported in volume for this device. Consult the local AMD sales office to confirm availability of specific valid combinations and to check on newly released combinations.
Note:For the AM29LV128M Enhanced-VIO device, the last digit of the speed indicator specifies VIO range. Speed grades ending in 3 (such as 93, 103, etc.) indicate a 3 Volt VIO range; speed grades ending in 8 (such as 98, 108, etc.) indicate a 1.8V VIO range.
September 17, 2002
AM29LV128M
9
ADVANCE
INFORMATION
DEVICE BUS OPERATIONS
This section describes the requirements and use of the device bus operations, which are initiated through the internal command register. The command register itself does not occupy any addressable memory location. The register is a latch used to store the commands, along with the address and data information needed to execute the command. The contents of the Table 1. register serve as inputs to the internal state machine. The state machine outputs dictate the function of the device. Table 1 lists the device bus operations, the inputs and control levels they require, and the resulting output. The following subsections describe each of these operations in further detail.
Device Bus Operations
DQ8-DQ15
Operation Read Write (Program/Erase) Accelerated Program Standby Output Disable Reset Sector Group Protect (Note 2) Sector Group Unprotect (Note 2) Temporary Sector Group Unprotect
CE# L L L VCC 0.3 V L X L
OE# L H H X H X H
WE# H L L X H X L
RESET# H H H VCC 0.3 V H L VID
WP#
ACC
Addresses (Note 2) AIN AIN AIN X X X SA, A6 =L, A3=L, A2=L, A1=H, A0=L SA, A6=H, A3=L, A2=L, A1=H, A0=L AIN
DQ0- DQ7 DOUT
BYTE# = VIH DOUT
BYTE# = VIL DQ8-DQ14 = High-Z, DQ15 = A-1 High-Z High-Z High-Z X
X (Note 3) (Note 3) X X X H
X X VHH H X X X
(Note 4) (Note 4) (Note 4) (Note 4) High-Z High-Z High-Z (Note 4) High-Z High-Z High-Z X
L
H
L
VID
H
X
(Note 4)
X
X
X
X
X
VID
H
X
(Note 4) (Note 4)
High-Z
Legend: L = Logic Low = VIL, H = Logic High = VIH, VID = 11.5-12.5 V, VHH = 11.5-12.5 V, X = Don't Care, SA = Sector Address, AIN = Address In, DIN = Data In, DOUT = Data Out Notes: 1. Addresses are A22:A0 in word mode; A22:A-1 in byte mode. Sector addresses are A22:A15 in both modes. 2. The sector protect and sector unprotect functions may also be implemented via programming equipment. See the "Sector Protection and Unprotection" section. 3. If WP# = VIL, the first or last sector remains protected. If WP# = VIH, the first or last sector will be protected or unprotected as determined by the method described in "Sector Protection and Unprotection". All sectors are unprotected when shipped from the factory (The SecSi Sector may be factory protected depending on version ordered.) 4. DIN or DOUT as required by command sequence, data polling, or sector protect algorithm (see Figure 2).
Word/Byte Configuration
The BYTE# pin controls whether the device data I/O pins operate in the byte or word configuration. If the BYTE# pin is set at logic `1', the device is in word configuration, DQ0-DQ15 are active and controlled by CE# and OE#. If the BYTE# pin is set at logic `0', the device is in byte configuration, and only data I/O pins DQ0-DQ7 are active and controlled by CE# and OE#. The data I/O
pins DQ8-DQ14 are tri-stated, and the DQ15 pin is used as an input for the LSB (A-1) address function.
Enhanced VersatileIO (VIO) Control
The VersatileIOTM (VIO) control allows the host system to set the voltage levels that the device generates and tolerates on all I/Os and control inputs to the same voltage level that is asserted on VIO. See Ordering Information for VIO options on this device.
10
AM29LV128M
September 17, 2002
ADVANCE
INFORMATION Unlock Bypass mode, only two write cycles are required to program a word or byte, instead of four. The "Word/Byte Program Command Sequence" section has details on programming data to the device using both standard and Unlock Bypass command sequences. An erase operation can erase one sector, multiple sectors, or the entire device. Table 2 indicates the address space that each sector occupies. Refer to the DC Characteristics table for the active current specification for the write mode. The AC Characteristics section contains timing specification tables and timing diagrams for write operations. Write Buffer Write Buffer Programming allows the system write to a maximum of 16 words/32 bytes in one programming operation. This results in faster effective programming time than the standard programming algorithms. See "Write Buffer" for more information. Accelerated Program Operation The device offers accelerated program operations through the ACC function. This is one of two functions provided by the WP#/ACC pin. This function is primarily intended to allow faster manufacturing throughput at the factory. If the system asserts VHH on this pin, the device automatically enters the aforementioned Unlock Bypass mode, temporarily unprotects any protected sectors, and uses the higher voltage on the pin to reduce the time required for program operations. The system would use a two-cycle program command sequence as required by the Unlock Bypass mode. Removing VHH from the WP#/ACC pin returns the device to normal operation. Note that the WP#/ACC pin must not be at VHH for operations other than accelerated programming, or device damage may result. WP# has an internal pullup; when unconnected, WP# is at VIH. Autoselect Functions If the system writes the autoselect command sequence, the device enters the autoselect mode. The system can then read autoselect codes from the internal register (which is separate from the memory array) on DQ7-DQ0. Standard read cycle timings apply in this mode. Refer to the Autoselect Mode and Autoselect Command Sequence sections for more information.
For example, a VI/O of 1.65-3.6 volts allows for I/O at the 1.8 or 3 volt levels, driving and receiving signals to and from other 1.8 or 3 V devices on the same data bus.
Requirements for Reading Array Data
To read array data from the outputs, the system must drive the CE# and OE# pins to VIL. CE# is the power control and selects the device. OE# is the output control and gates array data to the output pins. WE# should remain at VIH. The internal state machine is set for reading array data upon device power-up, or after a hardware reset. This ensures that no spurious alteration of the memory content occurs during the power transition. No command is necessary in this mode to obtain array data. Standard microprocessor read cycles that assert valid addresses on the device address inputs produce valid data on the device data outputs. The device remains enabled for read access until the command register contents are altered. See "Reading Array Data" for more information. Refer to the AC Read-Only Operations table for timing specifications and to Figure 13 for the timing diagram. Refer to the DC Characteristics table for the active current specification on reading array data. Page Mode Read The device is capable of fast page mode read and is compatible with the page mode Mask ROM read operation. This mode provides faster read access speed for random locations within a page. The page size of the device is 4 words/8 bytes. The appropriate page is selected by the higher address bits A(max)-A2. Address bits A1-A0 in word mode (A1-A-1 in byte mode) determine the specific word within a page. This is an asynchronous operation; the microprocessor supplies the specific word location. The random or initial page access is equal to tACC or tCE and subsequent page read accesses (as long as the locations specified by the microprocessor falls within that page) is equivalent to tPACC. When CE# is deasserted and reasserted for a subsequent access, the access time is tACC or t CE . Fast page mode accesses are obtained by keeping the "read-page addresses" constant and changing the "intra-read page" addresses.
Writing Commands/Command Sequences
To write a command or command sequence (which includes programming data to the device and erasing sectors of memory), the system must drive WE# and CE# to VIL, and OE# to VIH. The device features an Unlock Bypass mode to facilitate faster programming. Once the device enters the
Standby Mode
When the system is not reading or writing to the device, it can place the device in the standby mode. In this mode, current consumption is greatly reduced,
September 17, 2002
AM29LV128M
11
ADVANCE
INFORMATION
and the outputs are placed in the high impedance state, independent of the OE# input. The device enters the CMOS standby mode when the CE# and RESET# pins are both held at VIO 0.3 V. (Note that this is a more restricted voltage range than VIH.) If CE# and RESET# are held at VIH, but not within VIO 0.3 V, the device will be in the standby mode, but the standby current will be greater. The device requires standard access time (t CE ) for read access when the device is in either of these standby modes, before it is ready to read data. If the device is deselected during erasure or programming, the device draws active current until the operation is completed. Refer to the DC Characteristics table for the standby current specification.
RESET#: Hardware Reset Pin
The RESET# pin provides a hardware method of resetting the device to reading array data. When the RESET# pin is driven low for at least a period of tRP, the device immediately terminates any operation in progress, tristates all output pins, and ignores all read/write commands for the duration of the RESET# pulse. The device also resets the internal state machine to reading array data. The operation that was interrupted should be reinitiated once the device is ready to accept another command sequence, to ensure data integrity. Current is reduced for the duration of the RESET# pulse. When RESET# is held at VSS0.3 V, the device draws CMOS standby current (ICC4). If RESET# is held at VIL but not within VSS0.3 V, the standby current will be greater. The RESET# pin may be tied to the system reset circuitry. A system reset would thus also reset the Flash memory, enabling the system to read the boot-up firmware from the Flash memory. Refer to the AC Characteristics tables for RESET# parameters and to Figure 15 for the timing diagram.
Automatic Sleep Mode
The automatic sleep mode minimizes Flash device energy consumption. The device automatically enables this mode when addresses remain stable for tACC + 30 ns. The automatic sleep mode is independent of the CE#, WE#, and OE# control signals. Standard address access timings provide new data when addresses are changed. While in sleep mode, output data is latched and always available to the system. Refer to the DC Characteristics table for the automatic sleep mode current specification.
Output Disable Mode
When the OE# input is at VIH, output from the device is disabled. The output pins are placed in the high impedance state.
12
AM29LV128M
September 17, 2002
ADVANCE Table 2.
INFORMATION Sector Address Table
Sector Size (Kbytes/Kwords) 8-bit Address Range (in hexadecimal) 000000-00FFFF 010000-01FFFF 020000-02FFFF 030000-03FFFF 040000-04FFFF 050000-05FFFF 060000-06FFFF 070000-07FFFF 080000-08FFFF 090000-09FFFF 0A0000-0AFFFF 0B0000-0BFFFF 0C0000-0CFFFF 0D0000-0DFFFF 0E0000-0EFFFF 0F0000-0FFFFF 100000-10FFFF 110000-11FFFF 120000-12FFFF 130000-13FFFF 140000-14FFFF 150000-15FFFF 160000-16FFFF 170000-17FFFF 180000-18FFFF 190000-19FFFF 1A0000-1AFFFF 1B0000-1BFFFF 1C0000-1CFFFF 1D0000-1DFFFF 1E0000-1EFFFF 1F0000-1FFFFF 200000-20FFFF 210000-21FFFF 220000-22FFFF 230000-23FFFF 240000-24FFFF 250000-25FFFF 260000-26FFFF 270000-27FFFF 280000-28FFFF 290000-29FFFF 2A0000-2AFFFF 2B0000-2BFFFF 2C0000-2CFFFF 2D0000-2DFFFF 2E0000-2EFFFF 16-bit Address Range (in hexadecimal) 000000-007FFF 008000-00FFFF 010000-017FFF 018000-01FFFF 020000-027FFF 028000-02FFFF 030000-037FFF 038000-03FFFF 040000-047FFF 048000-04FFFF 050000-057FFF 058000-05FFFF 060000-067FFF 068000-06FFFF 070000-077FFF 078000-07FFFF 080000-087FFF 088000-08FFFF 090000-097FFF 098000-09FFFF 0A0000-0A7FFF 0A8000-0AFFFF 0B0000-0B7FFF 0B8000-0BFFFF 0C0000-0C7FFF 0C8000-0CFFFF 0D0000-0D7FFF 0D8000-0DFFFF 0E0000-0E7FFF 0E8000-0EFFFF 0F0000-0F7FFF 0F8000-0FFFFF 100000-107FFF 108000-10FFFF 110000-117FFF 118000-11FFFF 120000-127FFF 128000-12FFFF 130000-137FFF 138000-13FFFF 140000-147FFF 148000-14FFFF 150000-157FFF 158000-15FFFF 160000-167FFF 168000-16FFFF 170000-177FFF
Sector SA0 SA1 SA2 SA3 SA4 SA5 SA6 SA7 SA8 SA9 SA10 SA11 SA12 SA13 SA14 SA15 SA16 SA17 SA18 SA19 SA20 SA21 SA22 SA23 SA24 SA25 SA26 SA27 SA28 SA29 SA30 SA31 SA32 SA33 SA34 SA35 SA36 SA37 SA38 SA39 SA40 SA41 SA42 SA43 SA44 SA45 SA46 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
A22-A15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0
64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32
September 17, 2002
AM29LV128M
13
ADVANCE Table 2.
INFORMATION
Sector Address Table (Continued)
Sector Size (Kbytes/Kwords) 8-bit Address Range (in hexadecimal) 2F0000-2FFFFF 300000-30FFFF 310000-31FFFF 320000-32FFFF 330000-33FFFF 340000-34FFFF 350000-35FFFF 360000-36FFFF 370000-37FFFF 380000-38FFFF 390000-39FFFF 3A0000-3AFFFF 3B0000-3BFFFF 3C0000-3CFFFF 3D0000-3DFFFF 3E0000-3EFFFF 3F0000-3FFFFF 400000-40FFFF 410000-41FFFF 420000-42FFFF 430000-43FFFF 440000-44FFFF 450000-45FFFF 460000-46FFFF 470000-47FFFF 480000-48FFFF 490000-49FFFF 4A0000-4AFFFF 4B0000-4BFFFF 4C0000-4CFFFF 4D0000-4DFFFF 4E0000-4EFFFF 4F0000-4FFFFF 500000-50FFFF 510000-51FFFF 520000-52FFFF 530000-53FFFF 540000-54FFFF 550000-55FFFF 560000-56FFFF 570000-57FFFF 580000-58FFFF 590000-59FFFF 5A0000-5AFFFF 5B0000-5BFFFF 5C0000-5CFFFF 5D0000-5DFFFF 5E0000-5EFFFF 16-bit Address Range (in hexadecimal) 178000-17FFFF 180000-187FFF 188000-18FFFF 190000-197FFF 198000-19FFFF 1A0000-1A7FFF 1A8000-1AFFFF 1B0000-1B7FFF 1B8000-1BFFFF 1C0000-1C7FFF 1C8000-1CFFFF 1D0000-1D7FFF 1D8000-1DFFFF 1E0000-1E7FFF 1E8000-1EFFFF 1F0000-1F7FFF 1F8000-1FFFFF 200000-207FFF 208000-20FFFF 210000-217FFF 218000-21FFFF 220000-227FFF 228000-22FFFF 230000-237FFF 238000-23FFFF 240000-247FFF 248000-24FFFF 250000-257FFF 258000-25FFFF 260000-267FFF 268000-26FFFF 270000-277FFF 278000-27FFFF 280000-287FFF 288000-28FFFF 290000-297FFF 298000-29FFFF 2A0000-2A7FFF 2A8000-2AFFFF 2B0000-2B7FFF 2B8000-2BFFFF 2C0000-2C7FFF 2C8000-2CFFFF 2D0000-2D7FFF 2D8000-2DFFFF 2E0000-2E7FFF 2E8000-2EFFFF 2F0000-2F7FFF
Sector SA47 SA48 SA49 SA50 SA51 SA52 SA53 SA54 SA55 SA56 SA57 SA58 SA59 SA60 SA61 SA62 SA63 SA64 SA65 SA66 SA67 SA68 SA69 SA70 SA71 SA72 SA73 SA74 SA75 SA76 SA77 SA78 SA79 SA80 SA81 SA82 SA83 SA84 SA85 SA86 SA87 SA88 SA89 SA90 SA91 SA92 SA93 SA94 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
A22-A15 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0
64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32
14
AM29LV128M
September 17, 2002
ADVANCE Table 2.
INFORMATION
Sector Address Table (Continued)
Sector Size (Kbytes/Kwords) 8-bit Address Range (in hexadecimal) 5F0000-5FFFFF 600000-60FFFF 610000-61FFFF 620000-62FFFF 630000-63FFFF 640000-64FFFF 650000-65FFFF 660000-66FFFF 670000-67FFFF 680000-68FFFF 690000-69FFFF 6A0000-6AFFFF 6B0000-6BFFFF 6C0000-6CFFFF 6D0000-6DFFFF 6E0000-6EFFFF 6F0000-6FFFFF 700000-70FFFF 710000-71FFFF 720000-72FFFF 730000-73FFFF 740000-74FFFF 750000-75FFFF 760000-76FFFF 770000-77FFFF 780000-78FFFF 790000-79FFFF 7A0000-7AFFFF 7B0000-7BFFFF 7C0000-7CFFFF 7D0000-7DFFFF 7E0000-7EFFFF 7F0000-7FFFFF 800000-80FFFF 810000-81FFFF 820000-82FFFF 830000-83FFFF 840000-84FFFF 850000-85FFFF 860000-86FFFF 870000-87FFFF 880000-88FFFF 890000-89FFFF 8A0000-8AFFFF 8B0000-8BFFFF 8C0000-8CFFFF 8D0000-8DFFFF 8E0000-8EFFFF 16-bit Address Range (in hexadecimal) 2F8000-2FFFFF 300000-307FFF 308000-30FFFF 310000-317FFF 318000-31FFFF 320000-327FFF 328000-32FFFF 330000-337FFF 338000-33FFFF 340000-347FFF 348000-34FFFF 350000-357FFF 358000-35FFFF 360000-367FFF 368000-36FFFF 370000-377FFF 378000-37FFFF 380000-387FFF 388000-38FFFF 390000-397FFF 398000-39FFFF 3A0000-3A7FFF 3A8000-3AFFFF 3B0000-3B7FFF 3B8000-3BFFFF 3C0000-3C7FFF 3C8000-3CFFFF 3D0000-3D7FFF 3D8000-3DFFFF 3E0000-3E7FFF 3E8000-3EFFFF 3F0000-3F7FFF 3F8000-3FFFFF 400000-407FFF 408000-40FFFF 410000-417FFF 418000-41FFFF 420000-427FFF 428000-42FFFF 430000-437FFF 438000-43FFFF 440000-447FFF 448000-44FFFF 450000-457FFF 458000-45FFFF 460000-467FFF 468000-46FFFF 470000-477FFF
Sector SA95 SA96 SA97 SA98 SA99 SA100 SA101 SA102 SA103 SA104 SA105 SA106 SA107 SA108 SA109 SA110 SA111 SA112 SA113 SA114 SA115 SA116 SA117 SA118 SA119 SA120 SA121 SA122 SA123 SA124 SA125 SA126 SA127 SA128 SA129 SA130 SA131 SA132 SA133 SA134 SA135 SA136 SA137 SA138 SA139 SA140 SA141 SA142 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
A22-A15 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0
64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32
September 17, 2002
AM29LV128M
15
ADVANCE Table 2.
INFORMATION
Sector Address Table (Continued)
Sector Size (Kbytes/Kwords) 8-bit Address Range (in hexadecimal) 8F0000-8FFFFF 900000-90FFFF 910000-91FFFF 920000-92FFFF 930000-93FFFF 940000-94FFFF 950000-95FFFF 960000-96FFFF 970000-97FFFF 980000-98FFFF 990000-99FFFF 9A0000-9AFFFF 9B0000-9BFFFF 9C0000-9CFFFF 9D0000-9DFFFF 9E0000-9EFFFF 9F0000-9FFFFF A00000-A0FFFF A10000-A1FFFF A20000-A2FFFF A30000-A3FFFF A40000-A4FFFF A50000-A5FFFF A60000-A6FFFF A70000-A7FFFF A80000-A8FFFF A90000-A9FFFF AA0000-AAFFFF AB0000-ABFFFF AC0000-ACFFFF AD0000-ADFFFF AE0000-AEFFFF AF0000-AFFFFF B00000-B0FFFF B10000-B1FFFF B20000-B2FFFF B30000-B3FFFF B40000-B4FFFF B50000-B5FFFF B60000-B6FFFF B70000-B7FFFF B80000-B8FFFF B90000-B9FFFF BA0000-BAFFFF BB0000-BBFFFF BC0000-BCFFFF BD0000-BDFFFF BE0000-BEFFFF 16-bit Address Range (in hexadecimal) 478000-47FFFF 480000-487FFF 488000-48FFFF 490000-497FFF 498000-49FFFF 4A0000-4A7FFF 4A8000-4AFFFF 4B0000-4B7FFF 4B8000-4BFFFF 4C0000-4C7FFF 4C8000-4CFFFF 4D0000-4D7FFF 4D8000-4DFFFF 4E0000-4E7FFF 4E8000-4EFFFF 4F0000-4F7FFF 4F8000-4FFFFF 500000-507FFF 508000-50FFFF 510000-517FFF 518000-51FFFF 520000-527FFF 528000-52FFFF 530000-537FFF 538000-53FFFF 540000-547FFF 548000-54FFFF 550000-557FFF 558000-55FFFF 560000-567FFF 568000-56FFFF 570000-577FFF 578000-57FFFF 580000-587FFF 588000-58FFFF 590000-597FFF 598000-59FFFF 5A0000-5A7FFF 5A8000-5AFFFF 5B0000-5B7FFF 5B8000-5BFFFF 5C0000-5C7FFF 5C8000-5CFFFF 5D0000-5D7FFF 5D8000-5DFFFF 5E0000-5E7FFF 5E8000-5EFFFF 5F0000-5F7FFF
Sector SA143 SA144 SA145 SA146 SA147 SA148 SA149 SA150 SA151 SA152 SA153 SA154 SA155 SA156 SA157 SA158 SA159 SA160 SA161 SA162 SA163 SA164 SA165 SA166 SA167 SA168 SA169 SA170 SA171 SA172 SA173 SA174 SA175 SA176 SA177 SA178 SA179 SA180 SA181 SA182 SA183 SA184 SA185 SA186 SA187 SA188 SA189 SA190 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
A22-A15 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0
64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32
16
AM29LV128M
September 17, 2002
ADVANCE Table 2.
INFORMATION
Sector Address Table (Continued)
Sector Size (Kbytes/Kwords) 8-bit Address Range (in hexadecimal) BF0000-BFFFFF C00000-C0FFFF C10000-C1FFFF C20000-C2FFFF C30000-C3FFFF C40000-C4FFFF C50000-C5FFFF C60000-C6FFFF C70000-C7FFFF C80000-C8FFFF C90000-C9FFFF CA0000-CAFFFF CB0000-CBFFFF CC0000-CCFFFF CD0000-CDFFFF CE0000-CEFFFF CF0000-CFFFFF D00000-D0FFFF D10000-D1FFFF D20000-D2FFFF D30000-D3FFFF D40000-D4FFFF D50000-D5FFFF D60000-D6FFFF D70000-D7FFFF D80000-D8FFFF D90000-D9FFFF DA0000-DAFFFF DB0000-DBFFFF DC0000-DCFFFF DD0000-DDFFFF DE0000-DEFFFF DF0000-DFFFFF E00000-E0FFFF E10000-E1FFFF E20000-E2FFFF E30000-E3FFFF E40000-E4FFFF E50000-E5FFFF E60000-E6FFFF E70000-E7FFFF E80000-E8FFFF E90000-E9FFFF EA0000-EAFFFF EB0000-EBFFFF EC0000-ECFFFF ED0000-EDFFFF EE0000-EEFFFF 16-bit Address Range (in hexadecimal) 5F8000-5FFFFF 600000-607FFF 608000-60FFFF 610000-617FFF 618000-61FFFF 620000-627FFF 628000-62FFFF 630000-637FFF 638000-63FFFF 640000-647FFF 648000-64FFFF 650000-657FFF 658000-65FFFF 660000-667FFF 668000-66FFFF 670000-677FFF 678000-67FFFF 680000-687FFF 688000-68FFFF 690000-697FFF 698000-69FFFF 6A0000-6A7FFF 6A8000-6AFFFF 6B0000-6B7FFF 6B8000-6BFFFF 6C0000-6C7FFF 6C8000-6CFFFF 6D0000-6D7FFF 6D8000-6DFFFF 6E0000-6E7FFF 6E8000-6EFFFF 6F0000-6F7FFF 6F8000-6FFFFF 700000-707FFF 708000-70FFFF 710000-717FFF 718000-71FFFF 720000-727FFF 728000-72FFFF 730000-737FFF 738000-73FFFF 740000-747FFF 748000-74FFFF 750000-757FFF 758000-75FFFF 760000-767FFF 768000-76FFFF 770000-777FFF
Sector SA191 SA192 SA193 SA194 SA195 SA196 SA197 SA198 SA199 SA200 SA201 SA202 SA203 SA204 SA205 SA206 SA207 SA208 SA209 SA210 SA211 SA212 SA213 SA214 SA215 SA216 SA217 SA218 SA219 SA220 SA221 SA222 SA223 SA224 SA225 SA226 SA227 SA228 SA229 SA230 SA231 SA232 SA233 SA234 SA235 SA236 SA237 SA238 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
A22-A15 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0
64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32
September 17, 2002
AM29LV128M
17
ADVANCE Table 2.
INFORMATION
Sector Address Table (Continued)
Sector Size (Kbytes/Kwords) 8-bit Address Range (in hexadecimal) EF0000-EFFFFF F00000-F0FFFF F10000-F1FFFF F20000-F2FFFF F30000-F3FFFF F40000-F4FFFF F50000-F5FFFF F60000-F6FFFF F70000-F7FFFF F80000-F8FFFF F90000-F9FFFF FA0000-FAFFFF FB0000-FBFFFF FC0000-FCFFFF FD0000-FDFFFF FE0000-FEFFFF FF0000-FFFFFF 16-bit Address Range (in hexadecimal) 778000-77FFFF 780000-787FFF 788000-78FFFF 790000-797FFF 798000-79FFFF 7A0000-7A7FFF 7A8000-7AFFFF 7B0000-7B7FFF 7B8000-7BFFFF 7C0000-7C7FFF 7C8000-7CFFFF 7D0000-7D7FFF 7D8000-7DFFFF 7E0000-7E7FFF 7E8000-7EFFFF 7F0000-7F7FFF 7F8000-7FFFFF
Sector SA239 SA240 SA241 SA242 SA243 SA244 SA245 SA246 SA247 SA248 SA249 SA250 SA251 SA252 SA253 SA254 SA255 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
A22-A15 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32
18
AM29LV128M
September 17, 2002
ADVANCE
INFORMATION In addition, when verifying sector protection, the sector address must appear on the appropriate highest order address bits (see Table 2). Table 3 shows the remaining address bits that are don't care. When all necessary bits have been set as required, the programming equipment may then read the corresponding identifier code on DQ7-DQ0. To access the autoselect codes in-system, the host system can issue the autoselect command via the command register, as shown in Tables 9 and 10. This method does not require VID. Refer to the Autoselect Command Sequence section for more information.
Autoselect Mode
The autoselect mode provides manufacturer and device identification, and sector protection verification, through identifier codes output on DQ7-DQ0. This mode is primarily intended for programming equipment to automatically match a device to be programmed with its corresponding programm ing algorithm. However, the autoselect codes can also be accessed in-system through the command register. When using programming equipment, the autoselect mode requires V ID on address pin A9. Address pins A6, A3, A2, A1, and A0 must be as shown in Table 3.
Table 3.
Description CE# OE# WE#
Autoselect Codes, (High Voltage Method)
A9 A8 to A7 X A6 A5 to A4 X A3 to A2 L L
A22 A14 to to A15 A10 X X
DQ8 to DQ15
A1 A0
BYTE# BYTE# = VIH = VIL
00 22 22 22 X X X X X X
DQ7 to DQ0
Manufacturer ID: AMD Device ID Cycle 1 Cycle 2 Cycle 3
L
L
H
VID
L
L L H H H
L H L H L
01h 7Eh 12h 00h 01h (protected), 00h (unprotected) 98h (factory locked), 18h (not factory locked)
L
L
H
X
X
VID
X
L
X
H H
Sector Protection Verification SecSi Sector Indicator Bit (DQ7), WP# protects highest address sector SecSi Sector Indicator Bit (DQ7), WP# protects lowest address sector
L
L
H
SA
X
VID
X
L
X
L
L
L
H
X
X
VID
X
L
X
L
H
H
X
X
L
L
H
X
X
VID
X
L
X
L
H
H
X
X
88h (factory locked), 08h (not factory locked)
Legend: L = Logic Low = VIL, H = Logic High = VIH, SA = Sector Address, X = Don't care.
Sector Protection and Unprotection
The hardware sector protection feature disables both program and erase operations in any sector. The hardware sector unprotection feature re-enables both program and erase operations in previously protected sectors. Sector protection/unprotection can be implemented via two methods. Sector protection/unprotection requires VID on the RESET# pin only, and can be implemented either in-system or via programming equipment. Figure 2 shows the algorithms and Figure 23 shows the timing diagram. This method uses standard microprocessor bus
cycle timing. For sector unprotect, all unprotected sectors must first be protected prior to the first sector unprotect write cycle. The device is shipped with all sectors unprotected. AMD offers the option of programming and protecting sectors at its factory prior to shipping the device through AMD's ExpressFlashTM Service. Contact an AMD representative for details. It is possible to determine whether a sector is protected or unprotected. See the Autoselect Mode section for details.
September 17, 2002
AM29LV128M
19
ADVANCE
INFORMATION
Write Protect (WP#)
The Write Protect function provides a hardware method of protecting the first or last sector without using VID . Write Protect is one of two functions provided by the WP#/ACC input. If the system asserts VIL on the WP#/ACC pin, the device disables program and erase functions in the first or last sector independently of whether those sectors were protected or unprotected using the method described in "Sector Protection and Unprotection". Note that if WP#/ACC is at V IL when the device is in the standby mode, the maximum input load current is increased. See the table in "DC Characteristics". If the system asserts VIH on the WP#/ACC pin, the device reverts to whether the first or last sector was previously set to be protected or unprotected using the method described in "Sector Protection and Unprotection". Note that WP# has an internal pullup; when unconnected, WP# is at VIH.
START
RESET# = VID (Note 1) Perform Erase or Program Operations
RESET# = VIH
Temporary Sector Unprotect Completed (Note 2)
Temporary Sector Unprotect
This feature allows temporary unprotection of previously protected sectors to change data in-system. The Sector Unprotect mode is activated by setting the RESET# pin to VID. During this mode, formerly protected sectors can be programmed or erased by selecting the sector addresses. Once VID is removed from the RESET# pin, all the previously protected sectors are protected again. Figure 1 shows the algorithm, and Figure 22 shows the timing diagrams, for this feature.
Notes: 1. All protected sectors unprotected (If WP# = VIL, the first or last sector will remain protected). 2. All previously protected sectors are protected once again.
Figure 1.
Temporary Sector Unprotect Operation
20
AM29LV128M
September 17, 2002
ADVANCE
INFORMATION
START PLSCNT = 1 RESET# = VID Wait 1 s Protect all sectors: The indicated portion of the sector protect algorithm must be performed for all unprotected sectors prior to issuing the first sector unprotect address
START PLSCNT = 1 RESET# = VID Wait 1 s
Temporary Sector Unprotect Mode
No
First Write Cycle = 60h? Yes Set up sector address Sector Protect: Write 60h to sector address with A6 = 0, A1 = 1, A0 = 0 Wait 150 s Verify Sector Protect: Write 40h to sector address with A6 = 0, A1 = 1, A0 = 0 Read from sector address with A6 = 0, A1 = 1, A0 = 0 No
No First Write Cycle = 60h? Yes All sectors protected? Yes Set up first sector address Sector Unprotect: Write 60h to sector address with A6 = 1, A1 = 1, A0 = 0
Temporary Sector Unprotect Mode
Increment PLSCNT
Reset PLSCNT = 1
Wait 15 ms Verify Sector Unprotect: Write 40h to sector address with A6 = 1, A1 = 1, A0 = 0
No No PLSCNT = 25? Yes Data = 01h?
Increment PLSCNT
Yes
No Yes No
Read from sector address with A6 = 1, A1 = 1, A0 = 0 Set up next sector address
Device failed
Protect another sector? No Remove VID from RESET#
PLSCNT = 1000? Yes
Data = 00h? Yes
Device failed Write reset command
Last sector verified? Yes
No
Sector Protect Algorithm
Sector Protect complete
Sector Unprotect Algorithm
Remove VID from RESET#
Write reset command Sector Unprotect complete
Figure 2.
In-System Sector Group Protect/Unprotect Algorithms
September 17, 2002
AM29LV128M
21
ADVANCE
INFORMATION vices are then shipped from AMD's factory with the SecSi Sector permanently locked. Contact an AMD representative for details on using AMD's ExpressFlash service. Customer Lockable: SecSi Sector NOT Programmed or Protected At the Factory As an alternative to the factory-locked version, the device may be ordered such that the customer may program and protect the 128-word/256 bytes SecSi sector. The system may program the SecSi Sector using the write-buffer, accelerated and/or unlock bypass methods, in addition to the standard programming command sequence. See Command Definitions. Programming and protecting the SecSi Sector must be used with caution since, once protected, there is no procedure available for unprotecting the SecSi Sector area and none of the bits in the SecSi Sector memory space can be modified in any way. The SecSi Sector area can be protected using one of the following procedures: s Write the three-cycle Enter SecSi Sector Region command sequence, and then follow the in-system sector protect algorithm as shown in Figure 2, except that RESET# may be at either VIH or VID. This allows in-system protection of the SecSi Sector without raising any device pin to a high voltage. Note that this method is only applicable to the SecSi Sector. s Write the three-cycle Enter SecSi Sector Region command sequence, and then use the alternate method of sector protection described in the "Sector Protection and Unprotection" section. Once the SecSi Sector is programmed, locked and verified, the system must write the Exit SecSi Sector Region command sequence to return to reading and writing within the remainder of the array.
SecSi (Secured Silicon) Sector Flash Memory Region
The SecSi (Secured Silicon) Sector feature provides a Flash memory region that enables permanent part identification through an Electronic Serial Number (ESN). The SecSi Sector is 128 words/256 bytes in length, and uses a SecSi Sector Indicator Bit (DQ7) to indicate whether or not the SecSi Sector is locked when shipped from the factory. This bit is permanently set at the factory and cannot be changed, which prevents cloning of a factory locked part. This ensures the security of the ESN once the product is shipped to the field. AMD offers the device with the SecSi Sector either factor y locked o r custom er locka ble . Th e factory-locked version is always protected when shipped from the factory, and has the SecSi (Secured Silicon) Sector Indicator Bit permanently set to a "1." The customer-lockable version is shipped with the SecSi Sector unprotected, allowing customers to program the sector after receiving the device. The customer-lockable version also has the SecSi Sector Indicator Bit permanently set to a "0." Thus, the SecSi Sector Indicator Bit prevents customer-lockable devices from being used to replace devices that are factory locked. The SecSi sector address space in this device is allocated as follows: Table 4.
SecSi Sector Address Range 000000h-000007h 000008h-00007Fh
SecSi Sector Contents
Customer Lockable
Standard ExpressFlash Factory Locked Factory Locked ESN Unavailable ESN or determined by customer Determined by customer
Determined by customer
The system accesses the SecSi Sector through a command sequence (see "Enter SecSi Sector/Exit SecSi Sector Command Sequence"). After the system has written the Enter SecSi Sector command sequence, it may read the SecSi Sector by using the addresses normally occupied by the first sector (SA0). This mode of operation continues until the system issues the Exit SecSi Sector command sequence, or until power is removed from the device. On power-up, or following a hardware reset, the device reverts to sending commands to sector SA0. Factory Locked: SecSi Sector Programmed and Protected At the Factory In devices with an ESN, the SecSi Sector is protected when the device is shipped from the factory. The SecSi Sector cannot be modified in any way. A factory locked device has an 8-word/16-byte random ESN at addresses 000000h-000007h. Customers may opt to have their code programmed by AMD through the AMD ExpressFlash service. The de-
Hardware Data Protection
The command sequence requirement of unlock cycles for programming or erasing provides data protection against inadvertent writes (refer to Tables 9 and 10 for command definitions). In addition, the following hardware data protection measures prevent accidental erasure or programming, which might otherwise be caused by spurious system level signals during VCC power-up and power-down transitions, or from system noise. Low VCC Write Inhibit When VCC is less than V LKO, the device does not accept any write cycles. This protects data during VCC power-up and power-down. The command register
22
AM29LV128M
September 17, 2002
ADVANCE
INFORMATION Logical Inhibit Write cycles are inhibited by holding any one of OE# = VIL, CE# = VIH or WE# = V IH. To initiate a write cycle, CE# and WE# must be a logical zero while OE# is a logical one. Power-Up Write Inhibit If WE# = CE# = VIL and OE# = VIH during power up, the device does not accept commands on the rising edge of WE#. The internal state machine is automatically reset to the read mode on power-up.
and all internal program/erase circuits are disabled, and the device resets to the read mode. Subsequent writes are ignored until VCC is greater than VLKO. The system must provide the proper signals to the control pins to prevent unintentional writes when V CC is greater than VLKO. Write Pulse "Glitch" Protection Noise pulses of less than 5 ns (typical) on OE#, CE# or WE# do not initiate a write cycle.
COMMON FLASH MEMORY INTERFACE (CFI)
The Common Flash Interface (CFI) specification outlines device and host system software interrogation handshake, which allows specific vendor-specified software algorithms to be used for entire families of devices. Software support can then be device-independent, JEDEC ID-independent, and forward- and backward-compatible for the specified flash device families. Flash vendors can standardize their existing interfaces for long-term compatibility. This device enters the CFI Query mode when the system writes the CFI Query command, 98h, to address 55h, any time the device is ready to read array data. The system can read CFI information at the addresses given in Tables 5-8. To terminate reading CFI data, the system must write the reset command. The system can also write the CFI query command when the device is in the autoselect mode. The device enters the CFI query mode, and the system can read CFI data at the addresses given in Tables 5-8. The system must write the reset command to return the device to the autoselect mode. For further information, please refer to the CFI Specification and CFI Publication 100, available via the World Wide Web at http://www.am d.com/products/nvd/overview/cfi.html. Alternatively, contact an AMD representative for copies of these documents.
Table 5.
Addresses (x16) 10h 11h 12h 13h 14h 15h 16h 17h 18h 19h 1Ah Data 0051h 0052h 0059h 0002h 0000h 0040h 0000h 0000h 0000h 0000h 0000h
CFI Query Identification String
Description
Query Unique ASCII string "QRY"
Primary OEM Command Set Address for Primary Extended Table Alternate OEM Command Set (00h = none exists) Address for Alternate OEM Extended Table (00h = none exists)
September 17, 2002
AM29LV128M
23
ADVANCE Table 6.
Addresses (x16) 1Bh 1Ch 1Dh 1Eh 1Fh 20h 21h 22h 23h 24h 25h 26h Data 0027h 0036h 0000h 0000h 0007h 0007h 000Ah 0000h 0001h 0005h 0004h 0000h
INFORMATION
System Interface String
Description
VCC Min. (write/erase) D7-D4: volt, D3-D0: 100 millivolt VCC Max. (write/erase) D7-D4: volt, D3-D0: 100 millivolt VPP Min. voltage (00h = no VPP pin present) VPP Max. voltage (00h = no VPP pin present) Typical timeout per single byte/word write 2N s Typical timeout for Min. size buffer write 2N s (00h = not supported) Typical timeout per individual block erase 2N ms Typical timeout for full chip erase 2N ms (00h = not supported) Max. timeout for byte/word write 2N times typical Max. timeout for buffer write 2N times typical Max. timeout per individual block erase 2N times typical Max. timeout for full chip erase 2N times typical (00h = not supported)
Table 7.
Addresses (x16) 27h 28h 29h 2Ah 2Bh 2Ch 2Dh 2Eh 2Fh 30h 31h 32h 33h 34h 35h 36h 37h 38h 39h 3Ah 3Bh 3Ch Data 0018h 0002h 0000h 0005h 0000h 0001h 00FFh 0000h 0000h 0001h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h
Device Geometry Definition
Description
Device Size = 2 byte Flash Device Interface description (refer to CFI publication 100) Max. number of byte in multi-byte write = 2N (00h = not supported) Number of Erase Block Regions within device (01h = uniform device, 02h = boot device) Erase Block Region 1 Information (refer to the CFI specification or CFI publication 100)
N
Erase Block Region 2 Information (refer to CFI publication 100)
Erase Block Region 3 Information (refer to CFI publication 100)
Erase Block Region 4 Information (refer to CFI publication 100)
24
AM29LV128M
September 17, 2002
ADVANCE Table 8.
Addresses (x16) 40h 41h 42h 43h 44h Data 0050h 0052h 0049h 0031h 0033h
INFORMATION
Primary Vendor-Specific Extended Query
Description Query-unique ASCII string "PRI" Major version number, ASCII Minor version number, ASCII Address Sensitive Unlock (Bits 1-0) 0 = Required, 1 = Not Required Process Technology (Bits 7-2) 0010b = 0.23 m MirrorBit
45h
0008h
46h 47h 48h 49h 4Ah 4Bh 4Ch 4Dh
0002h 0001h 0001h 0004h 0000h 0000h 0001h 00B5h
Erase Suspend 0 = Not Supported, 1 = To Read Only, 2 = To Read & Write Sector Protect 0 = Not Supported, X = Number of sectors in per group Sector Temporary Unprotect 00 = Not Supported, 01 = Supported Sector Protect/Unprotect scheme 04 = 29LV800 mode Simultaneous Operation 00 = Not Supported, X = Number of Sectors in Bank Burst Mode Type 00 = Not Supported, 01 = Supported Page Mode Type 00 = Not Supported, 01 = 4 Word Page, 02 = 8 Word Page ACC (Acceleration) Supply Minimum 00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV ACC (Acceleration) Supply Maximum 00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV Top/Bottom Boot Sector Flag
4Eh
00C5h
4Fh
0004h/ 0005h
00h = Uniform Device without WP# protect, 02h = Bottom Boot Device, 03h = Top Boot Device, 04h = Uniform sectors bottom WP# protect, 05h = Uniform sectors top WP# protect Program Suspend 00h = Not Supported, 01h = Supported
50h
0001h
COMMAND DEFINITIONS
Writing specific address and data commands or sequences into the command register initiates device operations. Tables 9 and 10 defines the valid register command sequences. Writing incorrect address and data values or writing them in the improper sequence may place the device in an unknown state. A reset command is then required to return the device to reading array data. All addresses are latched on the falling edge of WE# or CE#, whichever happens later. All data is latched on the rising edge of WE# or CE#, whichever happens first. Refer to the AC Characteristics section for timing diagrams.
Reading Array Data
The device is automatically set to reading array data after device power-up. No commands are required to retrieve data. The device is ready to read array data after completing an Embedded Program or Embedded Erase algorithm. After the device accepts an Erase Suspend command, the device enters the erase-suspend-read mode, after which the system can read data from any 25
September 17, 2002
AM29LV128M
ADVANCE
INFORMATION Tables 9 and 10 show the address and data requirements. This method is an alternative to that shown in Table 3, which is intended for PROM programmers and requires VID on address pin A9. The autoselect command sequence may be written to an address that is either in the read or erase-suspend-read mode. The autoselect command may not be written while the device is actively programming or erasing. The autoselect command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle that contains the autoselect command. The device then enters the autoselect mode. The system may read at any address any number of times without initiating another autoselect command sequence: s A read cycle at address XX00h returns the manufacturer code. s Three read cycles at addresses 01h, 0Eh, and 0Fh return the device code. s A read cycle to an address containing a sector address (SA), and the address 02h on A7-A0 in word mode returns 01h if the sector is protected, or 00h if it is unprotected. The system must write the reset command to return to the read mode (or erase-suspend-read mode if the device was previously in Erase Suspend).
non-erase-suspended sector. After completing a programming operation in the Erase Suspend mode, the system may once again read array data with the same exception. See the Erase Suspend/Erase Resume Commands section for more information. The system must issue the reset command to return the device to the read (or erase-suspend-read) mode if DQ5 goes high during an active program or erase operation, or if the device is in the autoselect mode. See the next section, Reset Command, for more information. See also Requirements for Reading Array Data in the Device Bus Operations section for more information. The Read-Only Operations table provides the read parameters, and Figure 13 shows the timing diagram.
Reset Command
Writing the reset command resets the device to the read or erase-suspend-read mode. Address bits are don't cares for this command. The reset command may be written between the sequence cycles in an erase command sequence before erasing begins. This resets the device to the read mode. Once erasure begins, however, the device ignores reset commands until the operation is complete. The reset command may be written between the sequence cycles in a program command sequence before programming begins. This resets the device to the read mode. If the program command sequence is written while the device is in the Erase Suspend mode, writing the reset command returns the device to the erase-suspend-read mode. Once programming begins, however, the device ignores reset commands until the operation is complete. The reset command may be written between the sequence cycles in an autoselect command sequence. Once in the autoselect mode, the reset command must be written to return to the read mode. If the device entered the autoselect mode while in the Erase Suspend mode, writing the reset command returns the device to the erase-suspend-read mode. If DQ5 goes high during a program or erase operation, writing the reset command returns the device to the read mode (or erase-suspend-read mode if the device was in Erase Suspend). Note that if DQ1 goes high during a Write Buffer Programming operation, the system must write the Write-to-Buffer-Abort Reset command sequence to reset the device for the next operation.
Enter SecSi Sector/Exit SecSi Sector Command Sequence
The SecSi Sector region provides a secured data area containing an 8-word/16-byte random Electronic Serial Number (ESN). The system can access the SecSi Sector region by issuing the three-cycle Enter SecSi Sector command sequence. The device continues to access the SecSi Sector region until the system issues the four-cycle Exit SecSi Sector command sequence. The Exit SecSi Sector command sequence returns the device to normal operation. Tables 9 and 10 show the address and data requirements for both command sequences. See also "SecSi (Secured Silicon) Sector Flash Memory Region" for further information.
Word/Byte Program Command Sequence
Programming is a four-bus-cycle operation. The program command sequence is initiated by writing two unlock write cycles, followed by the program set-up command. The program address and data are written next, which in turn initiate the Embedded Program algorithm. The system is not required to provide further controls or timings. The device automatically provides internally generated program pulses and verifies the programmed cell margin. Tables 9 and 10 show the address and data requirements for the word program command sequence.
Autoselect Command Sequence
The autoselect command sequence allows the host system to access the manufacturer and device codes, and determine whether or not a sector is protected. 26
AM29LV128M
September 17, 2002
ADVANCE
INFORMATION command written at the Sector Address in which programming will occur. The fourth cycle writes the sector address and the number of word locations, minus one, to be programmed. For example, if the system will program 6 unique address locations, then 05h should be written to the device. This tells the device how many write buffer addresses will be loaded with data and therefore when to expect the Program Buffer to Flash command. The number of locations to program cannot exceed the size of the write buffer or the operation will abort. The fifth cycle writes the first address location and data to be programmed. The write-buffer-page is selected by address bits A MAX-A 4 . All subsequent address/data pairs must fall within the selected-write-buffer-page. The system then writes the remaining address/data pairs into the write buffer. Write buffer locations may be loaded in any order. The write-buffer-page address must be the same for all address/data pairs loaded into the write buffer. (This means Write Buffer Programming cannot be performed across multiple write-buffer pages. This also means that Write Buffer Programming cannot be performed across multiple sectors. If the system attempts to load programming data outside of the selected write-buffer page, the operation will abort. Note that if a Write Buffer address location is loaded multiple times, the address/data pair counter will be decremented for every data load operation. The host s y s t e m m u s t th e r e f o r e a c c o u n t fo r l o a d i n g a write-buffer location more than once. The counter decrements for each data load operation, not for each unique write-buffer-address location. Note also that if an address location is loaded more than once into the buffer, the final data loaded for that address will be programmed. Once the specified number of write buffer locations have been loaded, the system must then write the Program Buffer to Flash command at the sector address. Any other address and data combination aborts the Write Buffer Programming operation. The device then begins programming. Data polling should be used while monitoring the last address location loaded into the write buffer. DQ7, DQ6, DQ5, and DQ1 should be monitored to determine the device status during Write Buffer Programming. The write-buffer programming operation can be suspended using the standard program suspend/resume commands. Upon successful completion of the Write Buffer Programming operation, the device is ready to execute the next command. The Write Buffer Programming Sequence can be aborted in the following ways:
When the Embedded Program algorithm is complete, the device then returns to the read mode and addresses are no longer latched. The system can determine the status of the program operation by using DQ7 or DQ6. Refer to the Write Operation Status section for information on these status bits. Any commands written to the device during the Embedded Program Algorithm are ignored. Note that a hardware reset immediately terminates the program operation. The program command sequence should be reinitiated once the device has returned to the read mode, to ensure data integrity. Programming is allowed in any sequence and across sector boundaries. A bit cannot be programmed from "0" back to a "1." Attempting to do so may cause the device to set DQ5 = 1, or cause the DQ7 and DQ6 status bits to indicate the operation was successful. However, a succeeding read will show that the data is still "0." Only erase operations can convert a "0" to a "1." Unlock Bypass Command Sequence The unlock bypass feature allows the system to program words to the device faster than using the standard program command sequence. The unlock bypass command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle containing the unlock bypass command, 20h. The device then enters the unlock bypass mode. A two-cycle unlock bypass program command sequence is all that is required to program in this mode. The first cycle in this sequence contains the unlock bypass program command, A0h; the second cycle contains the program address and data. Additional data is programmed in the same manner. This mode dispenses with the initial two unlock cycles required in the standard program command sequence, resulting in faster total programming time. Tables 9 and 10 show the requirements for the command sequence. During the unlock bypass mode, only the Unlock Bypass Program and Unlock Bypass Reset commands are valid. To exit the unlock bypass mode, the system must issue the two-cycle unlock bypass reset command sequence. The first cycle must contain the data 90h. The second cycle must contain the data 00h. The device then returns to the read mode. Write Buffer Programming Write Buffer Programming allows the system write to a maximum of 16 words/32 bytes in one programming operation. This results in faster effective programming time than the standard programming algorithms. The Write Buffer Programming command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle containing the Write Buffer Load
September 17, 2002
AM29LV128M
27
ADVANCE
INFORMATION from "0" back to a "1." Attempting to do so may cause the device to set DQ5 = 1, or cause the DQ7 and DQ6 status bits to indicate the operation was successful. However, a succeeding read will show that the data is still "0." Only erase operations can convert a "0" to a "1." Accelerated Program The device offers accelerated program operations through the WP#/ACC pin. When the system asserts VHH on the WP#/ACC pin, the device automatically enters the Unlock Bypass mode. The system may then write the two-cycle Unlock Bypass program command sequence. The device uses the higher voltage on the WP#/ACC pin to accelerate the operation. Note that the WP#/ACC pin must not be at V HH for operations other than accelerated programming, or device damage may result. WP# has an internal pullup; when unconnected, WP# is at VIH. Figure 4 illustrates the algorithm for the program operation. Refer to the Erase and Program Operations table in the AC Characteristics section for parameters, and Figure 16 for timing diagrams.
s Load a value that is greater than the page buffer size during the Number of Locations to Program step. s Write to an address in a sector different than the one specified during the Write-Buffer-Load command. s Write an Address/Data pair to a different write-buffer-page than the one selected by the Starting Address during the write buffer data loading stage of the operation. s Write data other than the Confirm Command after the specified number of data load cycles. The abort condition is indicated by DQ1 = 1, DQ7 = DATA# (for the last address location loaded), DQ6 = toggle, and DQ5=0. A Write-to-Buffer-Abort Reset command sequence must be written to reset the device for the next operation. Note that the full 3-cycle Write-to-Buffer-Abort Reset command sequence is required when using Write-Buffer-Programming features in Unlock Bypass mode. Programming is allowed in any sequence and across sector boundaries. A bit cannot be programmed
28
AM29LV128M
September 17, 2002
ADVANCE
INFORMATION
Write "Write to Buffer" command and Sector Address
Write number of addresses to program minus 1(WC) and Sector Address
Part of "Write to Buffer" Command Sequence
Write first address/data
Yes
WC = 0 ? No Abort Write to Buffer Operation? No Yes Write to buffer ABORTED. Must write "Write-to-buffer Abort Reset" command sequence to return to read mode. Write to a different sector address
(Note 1)
Write next address/data pair
WC = WC - 1
Write program buffer to flash sector address
Notes:
1. When Sector Address is specified, any address in the selected sector is acceptable. However, when loading Write-Buffer address locations with data, all addresses must fall within the selected Write-Buffer Page.
Read DQ7 - DQ0 at Last Loaded Address
2. 3.
DQ7 may change simultaneously with DQ5. Therefore, DQ7 should be verified. If this flowchart location was reached because DQ5= "1", then the device FAILED. If this flowchart location was reached because DQ1= "1", then the Write to Buffer operation was ABORTED. In either case, the proper reset command must be written before the device can begin another operation. If DQ1=1, write the Write-Buffer-Programming-Abort-Reset command. if DQ5=1, write the Reset command.
See Tables 9 and 10 for command sequences required for write buffer programming.
DQ7 = Data? No No DQ1 = 1? Yes DQ5 = 1? Yes Read DQ7 - DQ0 with address = Last Loaded Address No
Yes
4.
(Note 2)
DQ7 = Data? No
Yes
(Note 3)
FAIL or ABORT
PASS
Figure 3.
Write Buffer Programming Operation
September 17, 2002
AM29LV128M
29
ADVANCE
INFORMATION
Program Suspend/Program Resume Command Sequence
START
Write Program Command Sequence
Embedded Program algorithm in progress
Data Poll from System
The Program Suspend command allows the system to interrupt a programming operation or a Write to Buffer programming operation so that data can be read from any non-suspended sector. When the Program Suspend command is written during a programming process, the device halts the program operation within 15 s maximum (5 s typical) and updates the status bits. Addresses are not required when writing the Program Suspend command. After the programming operation has been suspended, the system can read array data from any non-suspended sector. The Program Suspend command may also be issued during a programming operation while an erase is suspended. In this case, data may be read from any addresses not in Erase Suspend or Program Suspend. If a read is needed from the SecSi Sector area (One-time Program area), then user must use the proper command sequences to enter and exit this region. The system may also write the autoselect command sequence when the device is in the Program Suspend mode. The system can read as many autoselect codes as required. When the device exits the autoselect mode, the device reverts to the Program Suspend mode, and is ready for another valid operation. See Autoselect Command Sequence for more information. After the Program Resume command is written, the device reverts to programming. The system can determine the status of the program operation using the DQ7 or DQ6 status bits, just as in the standard program operation. See Write Operation Status for more information. The system must write the Program Resume command (address bits are don't care) to exit the Program Suspend mode and continue the programming operation. Further writes of the Resume command are ignored. Another Program Suspend command can be written after the device has resume programming.
Verify Data?
No
Yes No
Increment Address
Last Address?
Yes Programming Completed
Note: See Tables 9 and 10 for program command sequence.
Figure 4.
Program Operation
30
AM29LV128M
September 17, 2002
ADVANCE
INFORMATION When the Embedded Erase algorithm is complete, the device returns to the read mode and addresses are no longer latched. The system can determine the status of the erase operation by using DQ7, DQ6, or DQ2. Refer to the Write Operation Status section for information on these status bits. Any commands written during the chip erase operation are ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs, the chip erase command sequence should be reinitiated once the device has returned to reading array data, to ensure data integrity. Figure 6 illustrates the algorithm for the erase operation. Refer to the Erase and Program Operations tables in the AC Characteristics section for parameters, and Figure 18 section for timing diagrams.
Program Operation or Write-to-Buffer Sequence in Progress
Write address/data XXXh/B0h
Write Program Suspend Command Sequence Command is also valid for Erase-suspended-program operations
Wait 1 ms
Read data as required
Autoselect and SecSi Sector read operations are also allowed Data cannot be read from erase- or program-suspended sectors
No
Done reading? Yes Write address/data XXXh/30h Write Program Resume Command Sequence
Sector Erase Command Sequence
Sector erase is a six bus cycle operation. The sector erase command sequence is initiated by writing two unlock cycles, followed by a set-up command. Two additional unlock cycles are written, and are then followed by the address of the sector to be erased, and the sector erase command. Table 10 shows the address and data requirements for the sector erase command sequence. The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically programs and verifies the entire memory for an all zero data pattern prior to electrical erase. The system is not required to provide any controls or timings during these operations. After the command sequence is written, a sector erase time-out of 50 s occurs. During the time-out period, additional sector addresses and sector erase commands may be written. Loading the sector erase buffer may be done in any sequence, and the number of sectors may be from one sector to all sectors. The time between these additional cycles must be less than 50 s, otherwise erasure may begin. Any sector erase address and command following the exceeded time-out may or may not be accepted. It is recommended that processor interrupts be disabled during this time to ensure all commands are accepted. The interrupts can be re-enabled after the last Sector Erase command is written. Any command other than S e ct o r E ra se o r E ra s e S u s p en d d u r i n g th e time-out period resets the device to the read mode. The system must rewrite the command sequence and any additional addresses and commands. The system can monitor DQ3 to determine if the sector erase timer has timed out (See the section on DQ3: Sector Erase Timer.). The time-out begins from the rising edge of the final WE# pulse in the command sequence.
Device reverts to operation prior to Program Suspend
Figure 5.
Program Suspend/Program Resume
Chip Erase Command Sequence
Chip erase is a six bus cycle operation. The chip erase command sequence is initiated by writing two unlock cycles, followed by a set-up command. Two additional unlock write cycles are then followed by the chip erase command, which in turn invokes the Embedded Erase algorithm. The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically preprograms and verifies the entire memory for an all zero data pattern prior to electrical erase. The system is not required to provide any controls or timings during these operations. Tables 9 and 10 show the address and data requirements for the chip erase command sequence.
September 17, 2002
AM29LV128M
31
ADVANCE
INFORMATION operation. However, when the Erase Suspend command is written during the sector erase time-out, the device immediately terminates the time-out period and suspends the erase operation. After the erase operation has been suspended, the device enters the erase-suspend-read mode. The system can read data from or program data to any sector not selected for erasure. (The device "erase suspends" all sectors selected for erasure.) Reading at any address within erase-suspended sectors produces status information on DQ7-DQ0. The system can use DQ7, or DQ6 and DQ2 together, to determine if a sector is actively erasing or is erase-suspended. Refer to the Write Operation Status section for information on these status bits. After an erase-suspended program operation is complete, the device returns to the erase-suspend-read mode. The system can determine the status of the program operation using the DQ7 or DQ6 status bits, just as in the standard word program operation. Refer to the Write Operation Status section for more information. In the erase-suspend-read mode, the system can also issue the autoselect command sequence. Refer to the Autoselect Mode and Autoselect Command Sequence sections for details. To resume the sector erase operation, the system must write the Erase Resume command. The address of the erase-suspended sector is required when writing this command. Further writes of the Resume command are ignored. Another Erase Suspend command can be written after the chip has resumed erasing.
When the Embedded Erase algorithm is complete, the device returns to reading array data and addresses are no longer latched. The system can determine the status of the erase operation by reading DQ7, DQ6, or DQ2 in the erasing sector. Refer to the Write Operation Status section for information on these status bits. Once the sector erase operation has begun, only the Erase Suspend command is valid. All other commands are ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs, the sector erase command sequence should be reinitiated once the device has returned to reading array data, to ensure data integrity. Figure 6 illustrates the algorithm for the erase operation. Refer to the Erase and Program Operations tables in the AC Characteristics section for parameters, and Figure 18 section for timing diagrams.
Erase Suspend/Erase Resume Commands
The Erase Suspend command, B0h, allows the system to interrupt a sector erase operation and then read data from, or program data to, any sector not selected for erasure. This command is valid only during the sector erase operation, including the 50 s time-out period during the sector erase command sequence. The Erase Suspend command is ignored if written during the chip erase operation or Embedded Program algorithm. When the Erase Suspend command is written during the sector erase operation, the device requires a typical of 5 s (maximum of 20 s) to suspend the erase
32
AM29LV128M
September 17, 2002
ADVANCE
INFORMATION
START
Write Erase Command Sequence (Notes 1, 2)
Data Poll to Erasing Bank from System
Embedded Erase algorithm in progress
No
Data = FFh?
Yes Erasure Completed
Notes: 1. See Tables 9 and 10 for erase command sequence. 2. See the section on DQ3 for information on the sector erase timer.
Figure 6.
Erase Operation
September 17, 2002
AM29LV128M
33
ADVANCE
INFORMATION
Command Definitions
Table 9.
Command Sequence (Note 1) Read (Note 6) Reset (Note 7) Autoselect (Note 8) Manufacturer ID Device ID (Note 9) SecSi Sector Factory Protect (Note 10) Sector Protect Verify (Note 12) Cycles
Command Definitions (x16 Mode, BYTE# = VIH)
Bus Cycles (Notes 2-5) First Second Addr Data Third Addr Data Fourth Addr Data Fifth Addr Data Sixth Addr Data
Addr RA XXX 555 555 555 555 555 555 555 555 SA 555 555 XXX XXX 555 555 BA BA 55
Data RD F0 AA AA AA AA AA AA AA AA 29 AA AA A0 90 AA AA B0 30 98
1 1 4 4 4 4 3 4 4 3 1 3 3 2 2 6 6 1 1 1
2AA 2AA 2AA 2AA 2AA 2AA 2AA 2AA 2AA 2AA PA XXX 2AA 2AA
55 55 55 55 55 55 55 55 55 55 PD 00 55 55
555 555 555 555 555 555 555 SA 555 555
90 90 90 90 88 90 A0 25 F0 20
X00 X01 X03 (SA)X02
0001 227E (Note 10) 00/01 X0E 2212 X0F 2200
Enter SecSi Sector Region Exit SecSi Sector Region Program Write to Buffer (Note 11) Program Buffer to Flash Write to Buffer Abort Reset (Note 13) Unlock Bypass Unlock Bypass Program (Note 14) Unlock Bypass Reset (Note 15) Chip Erase Sector Erase Program/Erase Suspend (Note 16) Program/Erase Resume (Note 17) CFI Query (Note 18)
XXX PA SA
00 PD WC PA PD WBL PD
555 555
80 80
555 555
AA AA
2AA 2AA
55 55
555 SA
10 30
Legend: X = Don't care RA = Read Address of the memory location to be read. RD = Read Data read from location RA during read operation. PA = Program Address. Addresses latch on the falling edge of the WE# or CE# pulse, whichever happens later. PD = Program Data for location PA. Data latches on the rising edge of WE# or CE# pulse, whichever happens first. Notes: 1. See Table 1 for description of bus operations. 2. 3. 4. 5. 6. 7. All values are in hexadecimal. Except for the read cycle and the fourth cycle of the autoselect command sequence, all bus cycles are write cycles. Data bits DQ15-DQ8 are don't care in command sequences, except for RD and PD. Unless otherwise noted, address bits A22-A11 are don't cares. No unlock or command cycles required when device is in read mode. The Reset command is required to return to the read mode (or to the erase-suspend-read mode if previously in Erase Suspend) when the device is in the autoselect mode, or if DQ5 goes high while the device is providing status information. The fourth cycle of the autoselect command sequence is a read cycle. Data bits DQ15-DQ8 are don't care. See the Autoselect Command Sequence section for more information. The device ID must be read in three cycles.
SA = Sector Address of sector to be verified (in autoselect mode) or erased. Address bits A22-A15 uniquely select any sector. WBL = Write Buffer Location. Address must be within the same write buffer page as PA. BC = Word Count. Number of write buffer locations to load minus 1.
lowest address sector, the data is 88h for factory locked and 08h for not factor locked. 11. The total number of cycles in the command sequence is determined by the number of words written to the write buffer. The maximum number of cycles in the command sequence is 21. 12. The data is 00h for an unprotected sector and 01h for a protected sector. 13. Command sequence resets device for next command after aborted write-to-buffer operation. 14. The Unlock Bypass command is required prior to the Unlock Bypass Program command. 15. The Unlock Bypass Reset command is required to return to the read mode when the device is in the unlock bypass mode. 16. The system may read and program in non-erasing sectors, or enter the autoselect mode, when in the Erase Suspend mode. The Erase Suspend command is valid only during a sector erase operation. 17. The Erase Resume command is valid only during the Erase Suspend mode.
18. Command is valid when device is ready to read array data or when device is in autoselect mode.
8.
9.
10. If WP# protects the highest address sector, the data is 98h for factory locked and 18h for not factory locked. If WP# protects the
34
AM29LV128M
September 17, 2002
ADVANCE Table 10.
Command Sequence (Note 1) Read (Note 6) Reset (Note 7) Autoselect (Note 8) Manufacturer ID Device ID (Note 9) SecSi Sector Factory Protect (Note 10) Sector Protect Verify (Note 12) Cycles
INFORMATION
Command Definitions (x8 Mode, BYTE# = VIL)
Bus Cycles (Notes 2-5) First Second Addr Data Third Addr Data Fourth Addr Data Fifth Addr Data Sixth Addr Data
Addr RA XXX AAA AAA AAA AAA AAA AAA AAA AAA SA AAA AAA XXX XXX AAA AAA BA BA AA
Data RD F0 AA AA AA AA AA AA AA AA 29 AA AA A0 90 AA AA B0 30 98
1 1 4 4 4 4 3 4 4 3 1 3 3 2 2 6 6 1 1 1
555 555 555 555 555 555 555 555 555 555 PA XXX 555 555
55 55 55 55 55 55 55 55 55 55 PD 00 55 55
AAA AAA AAA AAA AAA AAA AAA SA AAA AAA
90 90 90 90 88 90 A0 25 F0 20
X00 X02 X06 (SA)X04
01 7E (Note 10) 00/01 X1C 12 X1E 00
Enter SecSi Sector Region Exit SecSi Sector Region Program Write to Buffer (Note 11) Program Buffer to Flash Write to Buffer Abort Reset (Note 13) Unlock Bypass Unlock Bypass Program (Note 14) Unlock Bypass Reset (Note 15) Chip Erase Sector Erase Program/Erase Suspend (Note 16) Program/Erase Resume (Note 17) CFI Query (Note 18)
XXX PA SA
00 PD BC PA PD WBL PD
AAA AAA
80 80
AAA AAA
AA AA
555 555
55 55
AAA SA
10 30
Legend: X = Don't care RA = Read Address of the memory location to be read. RD = Read Data read from location RA during read operation. PA = Program Address. Addresses latch on the falling edge of the WE# or CE# pulse, whichever happens later. PD = Program Data for location PA. Data latches on the rising edge of WE# or CE# pulse, whichever happens first. Notes: 1. See Table 1 for description of bus operations. 2. 3. 4. 5. 6. 7. All values are in hexadecimal. Except for the read cycle and the fourth cycle of the autoselect command sequence, all bus cycles are write cycles. Data bits DQ15-DQ8 are don't care in command sequences, except for RD and PD. Unless otherwise noted, address bits A22-A11 are don't cares. No unlock or command cycles required when device is in read mode. The Reset command is required to return to the read mode (or to the erase-suspend-read mode if previously in Erase Suspend) when the device is in the autoselect mode, or if DQ5 goes high while the device is providing status information. The fourth cycle of the autoselect command sequence is a read cycle. Data bits DQ15-DQ8 are don't care. See the Autoselect Command Sequence section for more information. The device ID must be read in three cycles.
SA = Sector Address of sector to be verified (in autoselect mode) or erased. Address bits A22-A15 uniquely select any sector. WBL = Write Buffer Location. Address must be within the same write buffer page as PA. BC = Byte Count. Number of write buffer locations to load minus 1.
lowest address sector, the data is 88h for factory locked and 08h for not factor locked. 11. The total number of cycles in the command sequence is determined by the number of words written to the write buffer. The maximum number of cycles in the command sequence is 37. 12. The data is 00h for an unprotected sector group and 01h for a protected sector group. 13. Command sequence resets device for next command after aborted write-to-buffer operation. 14. The Unlock Bypass command is required prior to the Unlock Bypass Program command. 15. The Unlock Bypass Reset command is required to return to the read mode when the device is in the unlock bypass mode. 16. The system may read and program in non-erasing sectors, or enter the autoselect mode, when in the Erase Suspend mode. The Erase Suspend command is valid only during a sector erase operation. 17. The Erase Resume command is valid only during the Erase Suspend mode.
18. Command is valid when device is ready to read array data or when device is in autoselect mode.
8.
9.
10. If WP# protects the highest address sector, the data is 98h for factory locked and 18h for not factory locked. If WP# protects the
September 17, 2002
AM29LV128M
35
ADVANCE
INFORMATION
WRITE OPERATION STATUS
The device provides several bits to determine the status of a program or erase operation: DQ2, DQ3, DQ5, DQ6, and DQ7. Table 11 and the following subsections describe the function of these bits. DQ7 and DQ6 each offer a method for determining whether a program or erase operation is complete or in progress. The device also provides a hardware-based output signal, RY/BY#, to determine whether an Embedded Program or Erase operation is in progress or has been completed. valid data, the data outputs on DQ0-DQ6 may be still invalid. Valid data on DQ0-DQ7 will appear on successive read cycles. Table 11 shows the outputs for Data# Polling on DQ7. Figure 7 shows the Data# Polling algorithm. Figure 19 in the AC Characteristics section shows the Data# Polling timing diagram.
DQ7: Data# Polling
The Data# Polling bit, DQ7, indicates to the host system whether an Embedded Program or Erase algorithm is in progress or completed, or whether the device is in Erase Suspend. Data# Polling is valid after the rising edge of the final WE# pulse in the command sequence. During the Embedded Program algorithm, the device outputs on DQ7 the complement of the datum programmed to DQ7. This DQ7 status also applies to programming during Erase Suspend. When the Embedded Program algorithm is complete, the device outputs the datum programmed to DQ7. The system must provide the program address to read valid status information on DQ7. If a program address falls within a protected sector, Data# Polling on DQ7 is active for approximately 1 s, then the device returns to the read mode. During the Embedded Erase algorithm, Data# Polling produces a "0" on DQ7. When the Embedded Erase algorithm is complete, or if the device enters the Erase Suspend mode, Data# Polling produces a "1" on DQ7. The system must provide an address within any of the sectors selected for erasure to read valid status information on DQ7. After an erase command sequence is written, if all sectors selected for erasing are protected, Data# Polling on DQ7 is active for approximately 100 s, then the device returns to the read mode. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. However, if the system reads DQ7 at an address within a protected sector, the status may not be valid. Just prior to the completion of an Embedded Program or Erase operation, DQ7 may change asynchronously with DQ0-DQ6 while Output Enable (OE#) is asserted low. That is, the device may change from providing status information to valid data on DQ7. Depending on when the system samples the DQ7 output, it may read the status or valid data. Even if the device has completed the program or erase operation and DQ7 has
START
Read DQ7-DQ0 Addr = VA
DQ7 = Data?
Yes
No No
DQ5 = 1?
Yes Read DQ7-DQ0 Addr = VA
DQ7 = Data?
Yes
No FAIL PASS
Notes: 1. VA = Valid address for programming. During a sector erase operation, a valid address is any sector address within the sector being erased. During chip erase, a valid address is any non-protected sector address. 2. DQ7 should be rechecked even if DQ5 = "1" because DQ7 may change simultaneously with DQ5.
Figure 7.
Data# Polling Algorithm
36
AM29LV128M
September 17, 2002
ADVANCE
INFORMATION After an erase command sequence is written, if all sectors selected for erasing are protected, DQ6 toggles for approximately 100 s, then returns to reading array data. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. The system can use DQ6 and DQ2 together to determine whether a sector is actively erasing or is erase-suspended. When the device is actively erasing (that is, the Embedded Erase algorithm is in progress), DQ6 toggles. When the device enters the Erase Suspend mode, DQ6 stops toggling. However, the system must also use DQ2 to determine which sectors are erasing or erase-suspended. Alternatively, the system can use DQ7 (see the subsection on DQ7: Data# Polling). If a program address falls within a protected sector, DQ6 toggles for approximately 1 s after the program command sequence is written, then returns to reading array data. DQ6 also toggles during the erase-suspend-program mode, and stops toggling once the Embedded Program algorithm is complete. Table 11 shows the outputs for Toggle Bit I on DQ6. Figure 8 shows the toggle bit algorithm. Figure 20 in the "AC Characteristics" section shows the toggle bit timing diagrams. Figure 21 shows the differences between DQ2 and DQ6 in graphical form. See also the subsection on DQ2: Toggle Bit II.
RY/BY#: Ready/Busy#
The RY/BY# is a dedicated, open-drain output pin which indicates whether an Embedded Algorithm is in progress or complete. The RY/BY# status is valid after the rising edge of the final WE# pulse in the command sequence. Since RY/BY# is an open-drain output, several RY/BY# pins can be tied together in parallel with a pull-up resistor to VCC. If the output is low (Busy), the device is actively erasing or programming. (This includes programming in the Erase Suspend mode.) If the output is high (Ready), the device is in the read mode, the standby mode, or in the erase-suspend-read mode. Table 11 shows the outputs for RY/BY#.
DQ6: Toggle Bit I
Toggle Bit I on DQ6 indicates whether an Embedded Program or Erase algorithm is in progress or complete, or whether the device has entered the Erase Suspend mode. Toggle Bit I may be read at any address, and is valid after the rising edge of the final WE# pulse in the command sequence (prior to the program or erase operation), and during the sector erase time-out. During an Embedded Program or Erase algorithm operation, successive read cycles to any address cause DQ6 to toggle. The system may use either OE# or CE# to control the read cycles. When the operation is complete, DQ6 stops toggling.
September 17, 2002
AM29LV128M
37
ADVANCE
INFORMATION
DQ2: Toggle Bit II
START
Read DQ7-DQ0
The "Toggle Bit II" on DQ2, when used with DQ6, indicates whether a particular sector is actively erasing (that is, the Embedded Erase algorithm is in progress), or whether that sector is erase-suspended. Toggle Bit II is valid after the rising edge of the final WE# pulse in the command sequence. DQ2 toggles when the system reads at addresses within those sectors that have been selected for erasure. (The system may use either OE# or CE# to control the read cycles.) But DQ2 cannot distinguish whether the sector is actively erasing or is erase-suspended. DQ6, by comparison, indicates whether the device is actively erasing, or is in Erase Suspend, but cannot distinguish which sectors are selected for erasure. Thus, both status bits are required for sector and mode information. Refer to Table 11 to compare outputs for DQ2 and DQ6. Figure 8 shows the toggle bit algorithm in flowchart form, and the section "DQ2: Toggle Bit II" explains the algorithm. See also the RY/BY#: Ready/Busy# subsection. Figure 20 shows the toggle bit timing diagram. Figure 21 shows the differences between DQ2 and DQ6 in graphical form.
Read DQ7-DQ0
Toggle Bit = Toggle? Yes
No
No
DQ5 = 1?
Yes
Read DQ7-DQ0 Twice
Reading Toggle Bits DQ6/DQ2
Refer to Figure 8 for the following discussion. Whenever the system initially begins reading toggle bit status, it must read DQ7-DQ0 at least twice in a row to determine whether a toggle bit is toggling. Typically, the system would note and store the value of the toggle bit after the first read. After the second read, the system would compare the new value of the toggle bit with the first. If the toggle bit is not toggling, the device has completed the program or erase operation. The system can read array data on DQ7-DQ0 on the following read cycle. However, if after the initial two read cycles, the system determines that the toggle bit is still toggling, the system also should note whether the value of DQ5 is high (see the section on DQ5). If it is, the system should then determine again whether the toggle bit is toggling, since the toggle bit may have stopped toggling just as DQ5 went high. If the toggle bit is no longer toggling, the device has successfully completed the program or erase operation. If it is still toggling, the device did not completed the operation successfully, and the system must write the reset command to return to reading array data. The remaining scenario is that the system initially determines that the toggle bit is toggling and DQ5 has not gone high. The system may continue to monitor the toggle bit and DQ5 through successive read cycles, determining the status as described in the previous paragraph. Alternatively, it may choose to perform
Toggle Bit = Toggle?
No
Yes Program/Erase Operation Not Complete, Write Reset Command Program/Erase Operation Complete
Note: The system should recheck the toggle bit even if DQ5 = "1" because the toggle bit may stop toggling as DQ5 changes to "1." See the subsections on DQ6 and DQ2 for more information.
Figure 8.
Toggle Bit Algorithm
38
AM29LV128M
September 17, 2002
ADVANCE
INFORMATION mand. When the time-out period is complete, DQ3 switches from a "0" to a "1." If the time between additional sector erase commands from the system can be assumed to be less than 50 s, the system need not monitor DQ3. See also the Sector Erase Command Sequence section. After the sector erase command is written, the system should read the status of DQ7 (Data# Polling) or DQ6 (Toggle Bit I) to ensure that the device has accepted the command sequence, and then read DQ3. If DQ3 is "1," the Embedded Erase algorithm has begun; all further commands (except Erase Suspend) are ignored until the erase operation is complete. If DQ3 is "0," the device will accept additional sector erase commands. To ensure the command has been accepted, the system software should check the status of DQ3 prior to and following each subsequent sector erase command. If DQ3 is high on the second status check, the last command might not have been accepted. Table 11 shows the status of DQ3 relative to the other status bits.
other system tasks. In this case, the system must start at the beginning of the algorithm when it returns to determine the status of the operation (top of Figure 8).
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program, erase, or write-to-buffer time has exceeded a specified internal pulse count limit. Under these conditions DQ5 produces a "1," indicating that the program or erase cycle was not successfully completed. The device may output a "1" on DQ5 if the system tries to program a "1" to a location that was previously programmed to "0." Only an erase operation can change a "0" back to a "1." Under this condition, the device halts the operation, and when the timing limit has been exceeded, DQ5 produces a "1." In all these cases, the system must write the reset command to return the device to the reading the array (or to erase-suspend-read if the device was previously in the erase-suspend-program mode).
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the system may read DQ3 to determine whether or not erasure has begun. (The sector erase timer does not apply to the chip erase command.) If additional sectors are selected for erasure, the entire time-out also applies after each additional sector erase com-
DQ1: Write-to-Buffer Abort
DQ1 indicates whether a Write-to-Buffer operation was aborted. Under these conditions DQ1 produces a "1". The system must issue the Write-to-Buffer-Abort-Reset command sequence to return the device to reading array data. See Write Buffer
Table 11.
Status Embedded Program Algorithm Embedded Erase Algorithm Program-Suspended ProgramSector Suspend Non-Program Read Suspended Sector Erase-Suspended EraseSector Suspend Non-Erase Suspended Read Sector Erase-Suspend-Program (Embedded Program) Busy (Note 3) Abort (Note 4)
Write Operation Status
DQ6 Toggle Toggle DQ5 (Note 1) 0 0 DQ3 N/A 1 DQ2 (Note 2) No toggle Toggle DQ1 0 N/A RY/BY# 0 0 1 1 N/A Data Toggle N/A 1 1 N/A N/A N/A N/A N/A N/A N/A 0 1 0 0 0
Standard Mode Program Suspend Mode
DQ7 (Note 2) DQ7# 0
Invalid (not allowed) Data 1 No toggle 0
Erase Suspend Mode
DQ7# DQ7# DQ7#
Toggle Toggle Toggle
0 0 0
Write-toBuffer
Notes: 1. DQ5 switches to `1' when an Embedded Program, Embedded Erase, or Write-to-Buffer operation has exceeded the maximum timing limits. Refer to the section on DQ5 for more information. 2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details. 3. The Data# Polling algorithm should be used to monitor the last loaded write-buffer address location. 4. DQ1 switches to `1' when the device has aborted the write-to-buffer operation.
September 17, 2002
AM29LV128M
39
ADVANCE
INFORMATION
ABSOLUTE MAXIMUM RATINGS
Storage Temperature Plastic Packages . . . . . . . . . . . . . . . -65C to +150C Ambient Temperature with Power Applied . . . . . . . . . . . . . -55C to +125C Voltage with Respect to Ground VCC (Note 1) . . . . . . . . . . . . . . . . .-0.5 V to +4.0 V VIO . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to +4.0 V A9, OE#, ACC, and RESET# (Note 2) . . . . . . . . . . . . . . . . . . . .-0.5 V to +12.5 V All other pins (Note 1) . . . . . . -0.5 V to VCC +0.5 V Output Short Circuit Current (Note 3) . . . . . . 200 mA
Notes: 1. Minimum DC voltage on input or I/O pins is -0.5 V. During voltage transitions, input or I/O pins may overshoot V SS to -2.0 V for periods of up to 20 ns. Maximum DC voltage on input or I/O pins is VCC +0.5 V. See Figure 9. During voltage transitions, input or I/O pins may overshoot to VCC +2.0 V for periods up to 20 ns. See Figure 10. 2. Minimum DC input voltage on pins A9, OE#, ACC, and RESET# is -0.5 V. During voltage transitions, A9, OE#, ACC, and RESET# may overshoot V SS to -2.0 V for periods of up to 20 ns. See Figure 9. Maximum DC input voltage on pin A9, OE#, ACC, and RESET# is +12.5 V which may overshoot to +14.0 V for periods up to 20 ns. 3. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second. Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability. +0.8 V -0.5 V -2.0 V 20 ns 20 ns 20 ns
Figure 9. Maximum Negative Overshoot Waveform
20 ns VCC +2.0 V VCC +0.5 V 2.0 V 20 ns 20 ns
Figure 10. Maximum Positive Overshoot Waveform
OPERATING RANGES
Industrial (I) Devices Ambient Temperature (TA) . . . . . . . . . -40C to +85C Supply Voltages VCC (regulated voltage range) . . . . . . . . . . . 3.0-3.6 V VCC (full voltage range). . . . . . . . . . . . . . . . . 2.7-3.6 V VIO (Note 2) . . . . . . . . . . . . . . 1.65-1.95 or 2.7-3.0 V
Notes: 1. Operating ranges define those limits between which the functionality of the device is guaranteed. 2. See Ordering Information section for valid VCC/VIO range combinations.
40
AM29LV128M
September 17, 2002
ADVANCE
INFORMATION
DC CHARACTERISTICS CMOS Compatible
Parameter Symbol ILI ILIT ILO ICC1 ICC2 ICC3 ICC4 ICC5 ICC6 ICC7 Parameter Description (Notes) Input Load Current (1) A9, ACC Input Load Current Output Leakage Current VCC Active Read Current (2, 3) VCC Initial Page Read Current (2, 3) VCC Intra-Page Read Current (2, 3) VCC Active Write Current (3, 4) VCC Standby Current (3) VCC Reset Current (3) Automatic Sleep Mode (3, 5) Test Conditions VIN = VSS to VCC, VCC = VCC max VCC = VCC max; A9 = 12.5 V VOUT = VSS to VCC, VCC = VCC max 5 MHz CE# = VIL, OE# = VIH CE# = VIL, OE# = VIH CE# = VIL, OE# = VIH CE# = VIL, OE# = VIH CE#, RESET# = VCC 0.3 V, WP# = VIH RESET# = VSS 0.3 V, WP# = VIH VIH = VCC 0.3 V; VIL = VSS 0.3 V, WP# = VIH 3.0 V VIO Input Low Voltage (6) 1.8 V VIO 3.0 V VIO Input High Voltage (6) 1.8 V VIO Voltage for ACC Program Acceleration Voltage for Autoselect and Temporary Sector Unprotect Output Low Voltage VCC = 2.7-3.6 V VCC = 2.7-3.6 V IOL = 4.0 mA, VCC = VCC min = VIO IOL = 100 A, VCC = VCC min = VIO VOH VLKO Output High Voltage Low VCC Lock-Out Voltage (7) IOH = -2.0 mA, VCC = VCC min = VIO IOH = -100 A, VCC = VCC min = VIO 3.0 V VIO 1.8 V VIO 3.0 V VIO 1.8 V VIO 2.4 VIO - 0.1 2.3 2.5 V VIO - 0.4 11.5 11.5 VIO + 0.4 12.5 12.5 0.4 0.1 V V V V V V -0.4 2.0 0.4 VIO + 0.3 V V -0.5 1 MHz 15 15 30 10 50 1 1 1 Min Typ Max 1.0 35 1.0 20 mA 20 50 20 60 5 5 5 0.8 mA mA mA A A A V Unit A A A
VIL
VIH VHH VID
VOL
Notes: 1. On the WP#/ACC pin only, the maximum input load current when WP# = VIL is 5.0 A. 2. 3. 4. The ICC current listed is typically less than 2 mA/MHz, with OE# at VIH. Maximum ICC specifications are tested with VCC = VCCmax. ICC active while Embedded Erase or Embedded Program is in progress.
5.
Automatic sleep mode enables the low power mode when addresses remain stable for tACC + 30 ns. Typical sleep mode current is 200 nA. VIO voltage requirements. VCC = 3 V and VIO = 3 V or 1.8 V.
Not 100% tested.
6.
7.
September 17, 2002
AM29LV128M
41
ADVANCE
INFORMATION
TEST CONDITIONS
Table 12.
3.3 V Test Condition Output Load Output Load Capacitance, CL (including jig capacitance) CL 6.2 k Input Rise and Fall Times Input Pulse Levels Input timing measurement reference levels (See Note) Note: Diodes are IN3064 or equivalent Output timing measurement reference levels
Test Specifications
All Speeds 1 TTL gate 30 5 0.0-3.0 1.5 0.5 VIO pF ns V V V Unit
Device Under Test
2.7 k
Figure 11.
Test Setup
Note: If VIO < VCC, the reference level is 0.5 VIO.
KEY TO SWITCHING WAVEFORMS
WAVEFORM INPUTS Steady Changing from H to L Changing from L to H Don't Care, Any Change Permitted Does Not Apply Changing, State Unknown Center Line is High Impedance State (High Z) OUTPUTS
3.0 V 0.0 V
Input
1.5 V
Measurement Level
0.5 VIO V
Output
Note: If VIO < VCC, the input measurement reference level is 0.5 VIO.
Figure 12. Input Waveforms and Measurement Levels
42
AM29LV128M
September 17, 2002
ADVANCE
INFORMATION
AC CHARACTERISTICS Read-Only Operations
Parameter 93, 93R, 94, 94R Min CE#, OE# = V IL OE# = VIL Max Max Max Max Max Max Min Min Min 90 90 90 25 25 Speed Options 103, 103R, 108, 108R 100 100 100 30 30 25 25 0 0 10 113, 113R, 118, 118R 110 110 110 40 40 123, 123R, 128, 128R 120 120 120 40 40
JEDEC tAVAV tAVQV tELQV
Std. tRC tACC tCE tPACC
Description Read Cycle Time (Note 1) Address to Output Delay Chip Enable to Output Delay Page Access Time Output Enable to Output Delay Chip Enable to Output High Z (Note 1) Output Enable to Output High Z (Note 1) Output Hold Time From Addresses, CE# or OE#, Whichever Occurs First Read
Test Setup
Unit ns ns ns ns ns ns ns ns ns ns
tGLQV tEHQZ tGHQZ tAXQX
tOE tDF tDF tOH
tOEH
Output Enable Hold Time (Note 1)
Toggle and Data# Polling
Notes: 1. Not 100% tested. 2. See Figure 11 and Table 12 for test specifications.
tRC Addresses CE# tRH tRH OE# tOEH WE# HIGH Z Outputs RESET# RY/BY# Output Valid tCE tOH HIGH Z tOE tDF Addresses Stable tACC
0V
Figure 13.
Read Operation Timings
September 17, 2002
AM29LV128M
43
ADVANCE
INFORMATION
AC CHARACTERISTICS
A22-A2 Same Page
A1-A0*
Aa
tACC
Ab
tPACC
Ac
tPACC tPACC
Ad
Data Bus CE# OE#
Qa
Qb
Qc
Qd
* Figure shows word mode. Addresses are A1-A-1 for byte mode.
Figure 14.
Page Read Timings
44
AM29LV128M
September 17, 2002
ADVANCE
INFORMATION
AC CHARACTERISTICS Hardware Reset (RESET#)
Parameter JEDEC Std. tReady tReady tRP tRH tRPD Description RESET# Pin Low (During Embedded Algorithms) to Read Mode (See Note) RESET# Pin Low (NOT During Embedded Algorithms) to Read Mode (See Note) RESET# Pulse Width Reset High Time Before Read (See Note) RESET# Low to Standby Mode Max Max Min Min Min All Speed Options 20 500 500 50 20 Unit s ns ns ns s
Note: Not 100% tested.
RY/BY#
CE#, OE# tRH RESET# tRP tReady
Reset Timings NOT during Embedded Algorithms Reset Timings during Embedded Algorithms
tReady RY/BY# tRB CE#, OE#
RESET# tRP
Figure 15.
Reset Timings
September 17, 2002
AM29LV128M
45
ADVANCE
INFORMATION
AC CHARACTERISTICS Erase and Program Operations
Parameter JEDEC tAVAV tAVWL Std. tWC tAS tASO tWLAX tAH tAHT tDVWH tWHDX tDS tDH tOEPH tGHWL tELWL tWHEH tWLWH tWHDL tGHWL tCS tCH tWP tWPH Description Write Cycle Time (Note 1) Address Setup Time Address Setup Time to OE# low during toggle bit polling Address Hold Time Address Hold Time From CE# or OE# high during toggle bit polling Data Setup Time Data Hold Time Output Enable High during toggle bit polling Read Recovery Time Before Write (OE# High to WE# Low) CE# Setup Time CE# Hold Time Write Pulse Width Write Pulse Width High Write Buffer Program Operation (Notes 2, 3) Effective Write Buffer Program Operation (Notes 2, 4) Accelerated Effective Write Buffer Program Operation (Notes 2, 4) Per Byte Per Word Per Byte Per Word Byte Program Operation (Note 2) Word Accelerated Programming Operation (Note 2) tWHWH2 tWHWH2 tVHH tVCS Sector Erase Operation (Note 2) VHH Rise and Fall Time (Note 1) VCC Setup Time (Note 1) Byte Word Typ Typ Typ Typ Min Min 100 40 80 0.4 250 50 s s s sec ns s Min Min Min Min Min Min Min Min Min Min Min Min Min Typ Typ Typ Typ Typ Typ Speed Options 93, 93R, 103, 103R, 113, 113R, 123, 123R, 94, 94R 108, 108R 118, 118R 128, 128R 90 100 0 15 45 0 45 0 20 0 0 0 35 30 100 2.95 5.9 2.4 4.7 50 110 120 Unit ns ns ns ns ns ns ns ns ns ns ns ns ns s s s s s s
tWHWH1
tWHWH1
Notes: 1. Not 100% tested. 2. See the "Erase And Programming Performance" section for more information. 3. For 1-16 words/1-32 bytes programmed. 4. Effective write buffer specification is based upon a 16-word/32-byte write buffer operation.
46
AM29LV128M
September 17, 2002
ADVANCE
INFORMATION
AC CHARACTERISTICS
Program Command Sequence (last two cycles) tWC Addresses 555h tAS PA tAH CE# OE# tWP WE# tCS tDS Data tDH PD tBUSY RY/BY# Status DOUT tRB tWPH tWHWH1 PA PA Read Status Data (last two cycles)
tCH
A0h
VCC tVCS
otes: . PA = program address, PD = program data, DOUT is the true data at the program address. . Illustration shows device in word mode.
Figure 16.
Program Operation Timings
VHH
ACC
VIL or VIH tVHH tVHH
VIL or VIH
Figure 17.
Accelerated Program Timing Diagram
September 17, 2002
AM29LV128M
47
ADVANCE
INFORMATION
AC CHARACTERISTICS
Erase Command Sequence (last two cycles) tWC Addresses 2AAh tAS SA
555h for chip erase
Read Status Data
VA tAH
VA
CE#
OE# tWP WE# tCS tDS
tCH
tWPH
tWHWH2
tDH Data 55h 30h
10 for Chip Erase In Progress Complete
tBUSY RY/BY# tVCS VCC
tRB
Notes: 1. SA = sector address (for Sector Erase), VA = Valid Address for reading status data (see "Write Operation Status". 2. These waveforms are for the word mode.
Figure 18.
Chip/Sector Erase Operation Timings
48
AM29LV128M
September 17, 2002
ADVANCE
INFORMATION
AC CHARACTERISTICS
tRC Addresses VA tACC tCE CE# tCH OE# tOEH WE# tOH DQ7
High Z
VA
VA
tOE tDF
Complement
Complement
True
Valid Data
High Z
DQ0-DQ6 tBUSY RY/BY#
Status Data
Status Data
True
Valid Data
Note: VA = Valid address. Illustration shows first status cycle after command sequence, last status read cycle, and array data read cycle.
Figure 19.
Data# Polling Timings (During Embedded Algorithms)
September 17, 2002
AM29LV128M
49
ADVANCE
INFORMATION
AC CHARACTERISTICS
tAHT Addresses
tAS
tAHT tASO CE# tOEH WE# tOEPH OE# tDH DQ6/DQ2 Valid Data
Valid Status
tCEPH
tOE
Valid Status Valid Status
Valid Data
(first read) RY/BY#
(second read)
(stops toggling)
Note: VA = Valid address; not required for DQ6. Illustration shows first two status cycle after command sequence, last status read cycle, and array data read cycle
Figure 20.
Toggle Bit Timings (During Embedded Algorithms)
Enter Embedded Erasing WE#
Erase Suspend Erase
Enter Erase Suspend Program Erase Suspend Program
Erase Resume Erase Suspend Read Erase Erase Complete
Erase Suspend Read
DQ6
DQ2 Note: DQ2 toggles only when read at an address within an erase-suspended sector. The system may use OE# or CE# to toggle DQ2 and DQ6.
Figure 21.
DQ2 vs. DQ6
50
AM29LV128M
September 17, 2002
ADVANCE
INFORMATION
AC CHARACTERISTICS Temporary Sector Unprotect
Parameter JEDEC Std tVIDR tRSP Description VID Rise and Fall Time (See Note) RESET# Setup Time for Temporary Sector Unprotect Min Min All Speed Options 500 4 Unit ns s
Note: Not 100% tested.
VID RESET# VSS, VIL, or VIH tVIDR Program or Erase Command Sequence CE# tVIDR
VID VSS, VIL, or VIH
WE# tRSP RY/BY# tRRB
Figure 22.
Temporary Sector Group Unprotect Timing Diagram
September 17, 2002
AM29LV128M
51
ADVANCE
INFORMATION
AC CHARACTERISTICS
VID VIH
RESET#
SA, A6, A1, A0
Valid* Sector Group Protect or Unprotect
Valid* Verify 40h
Sector Group Protect: 150 s, Sector Group Unprotect: 15 ms
Valid*
Data
60h
60h
Status
1 s CE#
WE#
OE#
For sector group protect, A6 = 0, A1 = 1, A0 = 0. For sector group unprotect, A6 = 1, A1 = 1, A0 = 0.
Figure 23.
Sector Group Protect and Unprotect Timing Diagram
52
AM29LV128M
September 17, 2002
ADVANCE
INFORMATION
AC CHARACTERISTICS Alternate CE# Controlled Erase and Program Operations
Parameter JEDEC tAVAV tAVWL tELAX tDVEH tEHDX tGHEL tWLEL tEHWH tELEH tEHEL Std. tWC tAS tAH tDS tDH tGHEL tWS tWH tCP tCPH Description Write Cycle Time (Note 1) Address Setup Time Address Hold Time Data Setup Time Data Hold Time Read Recovery Time Before Write (OE# High to WE# Low) WE# Setup Time WE# Hold Time CE# Pulse Width CE# Pulse Width High Write Buffer Program Operation (Notes 2, 3) Effective Write Buffer Program Operation (Notes 2, 4) Effective Accelerated Write Buffer Program Operation (Notes 2, 4) Per Byte Per Word Per Byte Per Word Byte Program Operation (Note 2) Word Accelerated Programming Operation (Note 2) tWHWH2 tWHWH2 Sector Erase Operation (Note 2) Byte Word Typ Typ Typ Typ 100 40 80 0.4 s s s sec Min Min Min Min Min Min Min Min Min Min Typ Typ Typ Typ Typ Typ 93, 93R, 94, 94R 90 Speed Options 103, 103R, 113, 113R, 123, 123R, 108, 108R 118, 118R 128, 128R 100 0 45 45 0 0 0 0 45 30 100 2.95 5.9 2.4 4.7 50 110 120 Unit ns ns ns ns ns ns ns ns ns ns s s s s s s
tWHWH1
tWHWH1
Notes: 1. Not 100% tested. 2. See the "Erase And Programming Performance" section for more information. 3. For 1-16 words/1-32 bytes programmed. 4. Effective write buffer specification is based upon a 16-word/32-byte write buffer operation.
September 17, 2002
AM29LV128M
53
ADVANCE
INFORMATION
AC CHARACTERISTICS
555 for program 2AA for erase PA for program SA for sector erase 555 for chip erase
Data# Polling PA
Addresses tWC tWH WE# tGHEL OE# tCP CE# tWS tCPH tDS tDH Data tRH
A0 for program 55 for erase PD for program 30 for sector erase 10 for chip erase
tAS tAH
tWHWH1 or 2
tBUSY
DQ7#
DOUT
RESET#
Notes: RY/BY# 1. Figure indicates last two bus cycles of a program or erase operation. 2. PA = program address, SA = sector address, PD = program data. 3. DQ7# is the complement of the data written to the device. DOUT is the data written to the device. 4. Waveforms are for the word mode.
Figure 24.
Alternate CE# Controlled Write (Erase/Program) Operation Timings
LATCHUP CHARACTERISTICS
Description Input voltage with respect to VSS on all pins except I/O pins (including A9, OE#, and RESET#) Input voltage with respect to VSS on all I/O pins VCC Current Min -1.0 V -1.0 V -100 mA Max 12.5 V VCC + 1.0 V +100 mA
Note: Includes all pins except VCC. Test conditions: VCC = 3.0 V, one pin at a time.
54
AM29LV128M
September 17, 2002
ADVANCE
INFORMATION
ERASE AND PROGRAMMING PERFORMANCE
Parameter Sector Erase Time Chip Erase Time Effective Write Buffer Program Time (Note 3) Per Byte Per Word Byte Program Time Word Effective Accelerated Program Time (Note 3) Byte Word Byte Accelerated Program Time Word Chip Program Time (Note 4) 80 TBD TBD TBD s sec 100 2.4 4.7 40 218 TBD TBD TBD s s s s Excludes system level overhead (Note 6) Typ (Note 1) 0.4 90 2.95 5.9 50 105 210 TBD Max (Note 2) 15 Unit sec sec s s s Comments Excludes 00h programming prior to erasure (Note 5)
Notes: 1. Typical program and erase times assume the following conditions: 25C, 3.0 V VCC, 100,000 cycles. Additionally, programming typicals assume checkerboard pattern. 2. Under worst case conditions of 90C, VCC = 3.0 V, 100,000 cycles. 3. Effective write buffer specification is based upon a 16-word/32-byte write buffer operation. 4. The typical chip programming time is considerably less than the maximum chip programming time listed, since most words program faster than the maximum program times listed. 5. In the pre-programming step of the Embedded Erase algorithm, all bits are programmed to 00h before erasure. 6. System-level overhead is the time required to execute the two- or four-bus-cycle sequence for the program command. See Table 10 for further information on command definitions. 7. The device has a minimum erase and program cycle endurance of 100,000 cycles.
TSOP PIN AND BGA PACKAGE CAPACITANCE
Parameter Symbol CIN Parameter Description Input Capacitance Test Setup TSOP VIN = 0 BGA TSOP COUT Output Capacitance VOUT = 0 BGA TSOP CIN2 Control Pin Capacitance VIN = 0 BGA Typ 6 4.2 8.5 5.4 7.5 3.9 Max 7.5 5 12 6.5 9 4.7 Unit pF pF pF pF pF pF
Notes: 1. Sampled, not 100% tested. 2. Test conditions TA = 25C, f = 1.0 MHz.
DATA RETENTION
Parameter Description Minimum Pattern Data Retention Time 125C 20 Years Test Conditions 150C Min 10 Unit Years
September 17, 2002
AM29LV128M
55
ADVANCE
INFORMATION
PHYSICAL DIMENSIONS TS056/TSR056--56-Pin Standard/Reverse Thin Small Outline Package (TSOP)
PACKAGE JEDEC SYMBOL A A1 A2 b1 b c1 c D D1 E e L
O
TS/TSR 56 MO-142 (B) EC MIN. --0.05 0.95 0.17 0.17 0.10 0.10 19.90 18.30 13.90 0.50 0 0.08 NOM. ----1.00 0.20 0.22 ----20.00 18.40 14.00 0.50 BASIC 0.60 3 --56 0.70 5 0.20 MAX. 1.20 0.15 1.05 0.23 0.27 0.16 0.21 20.20 18.50 14.10
NOTES: 1 2 3 4 CONTROLLING DIMENSIONS ARE IN MILLIMETERS (mm). (DIMENSIONING AND TOLERANCING CONFORMS TO ANSI Y14.5M-1982.) PIN 1 IDENTIFIER FOR STANDARD PIN OUT (DIE UP). PIN 1 IDENTIFIER FOR REVERSE PIN OUT (DIE DOWN), INK OR LASER MARK. TO BE DETERMINED AT THE SEATING PLANE -C- . THE SEATING PLANE IS DEFINED AS THE PLANE OF CONTACT THAT IS MADE WHEN THE PACKAGE LEADS ARE ALLOWED TO REST FREELY ON A FLAT HORIZONTAL SURFACE. DIMENSIONS D1 AND E DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE MOLD PROTUSION IS 0.15 mm PER SIDE. DIMENSION b DOES NOT INCLUDE DAMBAR PROTUSION. ALLOWABLE DAMBAR PROTUSION SHALL BE 0.08 mm TOTAL IN EXCESS OF b DIMENSION AT MAX MATERIAL CONDITION. MINIMUM SPACE BETWEEN PROTRUSION AND AN ADJACENT LEAD TO BE 0.07 mm. THESE DIMESIONS APPLY TO THE FLAT SECTION OF THE LEAD BETWEEN 0.10 mm AND 0.25 mm FROM THE LEAD TIP. LEAD COPLANARITY SHALL BE WITHIN 0.10 mm AS MEASURED FROM THE SEATING PLANE. DIMENSION "e" IS MEASURED AT THE CENTERLINE OF THE LEADS.
3160\38.10A
5 6
7 8. 9
R N
56
AM29LV128M
September 17, 2002
ADVANCE
INFORMATION
PHYSICAL DIMENSIONS LAA064--64-Ball Fortified Ball Grid Array 13 x 11 mm Package
September 17, 2002
AM29LV128M
57
ADVANCE
INFORMATION
REVISION SUMMARY Revision A (October 3, 2001)
Initial release as abbreviated Advance Information data sheet.
Product Selector Guide Added 80-Ball Fine-Pitch BGA. Added Note #1. Added 103, 108, 113, 118, 123, 128 regulated OPNs. Changed all OPNs that end with 4 or 9 to 3 or 8. Program Suspend/Program Resume Command Sequence Changed 1ms to 15s maximum, with a typical of 5 s. Erase Suspend/Erase Resume Commands
Revision A+1 (March 20, 2002)
Distinctive Characteristics Clarified description of Enhanced VersatileIO control. Ordering Information Corrected device density in device number/description. Physical Dimensions Added drawing that shows both TS056 and TSR056 specifications.
Added that the device requires a typical of 5 s. Read-Only Operations, Erase Program Operations, and Alternate CE# Controlled Erase and Program Operations Added regulated OPNs. Changed all OPNs that end with 4 or 9 to 3 or 8.
Revision B (July 1, 2002)
Expanded data sheet to full specification version.
Revision B+1 (September 16, 2002)
Distinctive Characteristics, Physical Dimentions Added 80-Ball Fine-Pitch BGA.
Trademarks Copyright (c) 2002 Advanced Micro Devices, Inc. All rights reserved. AMD, the AMD logo, and combinations thereof are registered trademarks of Advanced Micro Devices, Inc. ExpressFlash is a trademark of Advanced Micro Devices, Inc. Product names used in this publication are for identification purposes only and may be trademarks of their respective companies.
58
AM29LV128M
September 17, 2002

▲Up To Search▲

Price & Availability of AM29LV128M

	To Download AM29LV128M Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .